American European bending tester
Test Purpose：
To determine if metal wires in children's products bend or break under stress, creating sharp edges or points that pose choking or injury hazards.
Compliance Standards：
- 16 CFR CPS USA: Child Product Safety Certification
- ASTM F963: Standard Consumer Safety Specification for Toy Products
- EN 71: European Toy Safety Directive
Test Methodology：
| Test Parameter | Specification |
|---|---|
| Deformation Test | Apply 3N axial force for 5 minutes |
| Bend Test | Flex the wire at 90° angle with 5mm radius mandrel |
| Edge Evaluation | Check for sharp edges using ISO 4671-1:2017 gauge |
Product advantages:
Ensures Child Safety: Directly tests for potential hazards from metal wires, significantly reducing the risk of cuts, punctures, or ingestion of broken pieces.
Dual Market Compliance: Designed to perform tests required by both US (ASTM, 16 CFR) and European (EN 71) standards, simplifying testing for manufacturers targeting both markets.
Objective and Quantifiable Results: Provides measurable outcomes (deformation percentage, breakage force) and a pass/fail assessment for sharp edges based on standardized methods.
Supports Design and Quality Control: Valuable for validating material choices, evaluating product design, and performing quality checks during manufacturing.
Reduces Risk of Recalls: Helps prevent costly and damaging product recalls by ensuring compliance with safety regulations before products are shipped.
Acceptance Criteria：
- No permanent deformation exceeding 15% of original length
- No sharp edges exceeding 0.5mm radius
- Maximum allowable breakage force ≥ 2N
在线联系供应商
Other supplier products
 |
Shoe Shank Stiffness Tester | Standard： SATRA TM256: Flexural and torsional stiffness testing for athletic, safety, and casual footwear. SATRA TM194: Dynamic fatigue resistanc... |
 |
QM Contact Coolness Tester | The sensation of coldness or warmth when skin touches an object is referred to as the “coldness and warmth feeling.” The feeling of col... |
 |
Wascator FOM 71 CLS Lab Washer - Extractor | Standards: ISO 5077/6330, M&S P1/P1A/P3A/P12/P91/P99/P99A/P13, BS EN25077/26330, NEXT TM7/7A/7B/TM12, GB/T 8629, IWSTM 31, IEC 456 Appl... |
 |
Shoe Abrasion Tester | Product Introduction: The whole shoe wear testing machine is used to test the wear resistance of soles and sole pieces. The principle is to press ... |
 |
Coating abrasion resistance tester | Product Introduction: The determination of scratch resistance of the coating is very similar to the scratch test of the coating, but this test met... |
Same products
 |
Air Permeability Tester STD- F8 | 卖方: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | 卖方: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | 卖方: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | 卖方: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | 卖方: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
