Carbide Rod With Coolant Hole
Carbide Rodswith One Coolant Duct
This blank is specially for some CNC blades or drills which needs duct for coolant to cool the increased heat during the high speed cutting or drilling. Standard specification and tolerance table please reference below.
|
Outer D(mm) |
OD Tol.(mm) |
Inner Hole d(mm) |
ID Tol.(mm) |
Hole center diviation value α |
Length（mm） |
L Tol.(mm) |
|
3.0 |
+0.50/+0.30 |
0.5 |
±0.10 |
0.10 |
330 |
+1.5 |
|
4.0 |
+0.50/+0.30 |
0.8 |
±0.10 |
0.10 |
330 |
+1.5 |
|
5.0 |
+0.50/+0.30 |
0.8 |
±0.10 |
0.13 |
330 |
+1.5 |
|
6.0 |
+0.50/+0.30 |
1.0 |
±0.15 |
0.15 |
330 |
+1.5 |
|
7.0 |
+0.60/+0.30 |
1.0 |
±0.15 |
0.15 |
330 |
+1.5 |
|
8.0 |
+0.60/+0.30 |
1.0 |
±0.15 |
0.15 |
330 |
+1.5 |
|
9.0 |
+0.60/+0.30 |
1.4 |
±0.15 |
0.20 |
330 |
+1.5 |
|
10.0 |
+0.60/+0.30 |
1.4 |
±0.15 |
0.20 |
330 |
+1.5 |
|
11.0 |
+0.60/+0.30 |
1.4 |
±0.15 |
0.28 |
330 |
+1.5 |
|
12.0 |
+0.60/+0.30 |
1.8 |
±0.15 |
0.30 |
330 |
+1.5 |
|
13.0 |
+0.70/+0.30 |
1.8 |
±0.15 |
0.34 |
330 |
+1.5 |
|
14.0 |
+0.70/+0.30 |
1.8 |
±0.15 |
0.37 |
330 |
+1.5 |
|
15.0 |
+0.70/+0.30 |
2.0 |
±0.20 |
0.40 |
330 |
+1.5 |
|
16.0 |
+0.70/+0.30 |
2.0 |
±0.20 |
0.40 |
330 |
+1.5 |
|
17.0 |
+0.80/+0.30 |
2.0 |
±0.20 |
0.47 |
330 |
+1.5 |
|
18.0 |
+0.80/+0.30 |
2.0 |
±0.20 |
0.50 |
330 |
+1.5 |
|
19.0 |
+0.80/+0.30 |
2.0 |
±0.20 |
0.50 |
330 |
+1.5 |
|
20.0 |
+0.80/+0.30 |
2.5 |
±0.25 |
0.50 |
330 |
+1.5 |
|
21.0 |
+0.80/+0.30 |
2.5 |
±0.25 |
0.50 |
330 |
+1.5 |
|
22.0 |
+0.80/+0.30 |
2.5 |
±0.25 |
0.50 |
330 |
+1.5 |
|
23.0 |
+0.80/+0.30 |
3.0 |
±0.25 |
0.50 |
330 |
+1.5 |
|
24.0 |
+0.80/+0.30 |
3.0 |
±0.25 |
0.50 |
330 |
+1.5 |
|
25.0 |
+0.80/+0.30 |
3.0 |
±0.25 |
0.50 |
330 |
+1.5 |
|
26.0 |
+0.80/+0.30 |
3.0 |
±0.25 |
0.50 |
330 |
+1.5 |
|
27.0 |
+0.80/+0.30 |
3.0 |
±0.25 |
0.50 |
330 |
+1.5 |
|
28.0 |
+0.80/+0.30 |
3.0 |
±0.25 |
0.50 |
330 |
+1.5 |
|
29.0 |
+0.80/+0.30 |
3.0 |
±0.25 |
0.50 |
330 |
+1.5 |
|
30.0 |
+0.80/+0.30 |
3.0 |
±0.25 |
0.50 |
330 |
+1.5 |
Carbide Rodswith Two Coolant Ducts, Straight
This blank is specially for some CNC blades or drills which needs duct for coolant to cool the increased heat during the high speed cutting or drilling. Standard specification and tolerance table please reference below.
Standard pitch
|
Outside Dia. Ø(mm) |
OD Tol. (mm) |
Inner d(mm) |
ID Tol.(mm) |
Distance between holds |
Hole center diviation value α |
L mm |
Tol. (mm) |
|
|
mm |
Tol. (mm) |
|||||||
|
6.0 |
+0.50/+0.30 |
0.8 |
±0.10 |
1.5 |
﹢0/-0.20 |
0.15 |
330 |
+1.5 |
|
7.0 |
+0.60/+0.30 |
0.8 |
±0.10 |
1.5 |
﹢0/-0.20 |
0.15 |
330 |
+1.5 |
|
8.0 |
+0.60/+0.30 |
1.0 |
±0.15 |
1.5 |
﹢0/-0.30 |
0.15 |
330 |
+1.5 |
|
9.0 |
+0.60/+0.30 |
1.0 |
±0.15 |
2.6 |
﹢0/-0.30 |
0.20 |
330 |
+1.5 |
|
10.0 |
+0.60/+0.30 |
1.0 |
±0.15 |
2.6 |
﹢0/-0.30 |
0.20 |
330 |
+1.5 |
|
11.0 |
+0.60/+0.30 |
1.2 |
±0.15 |
3.6 |
﹢0/-0.30 |
0.28 |
330 |
+1.5 |
|
12.0 |
+0.60/+0.30 |
1.2 |
±0.15 |
3.6 |
﹢0/-0.30 |
0.30 |
330 |
+1.5 |
|
13.0 |
+0.70/+0.30 |
1.2 |
±0.15 |
3.6 |
﹢0/-0.30 |
0.34 |
330 |
+1.5 |
|
14.0 |
+0.70/+0.30 |
1.5 |
±0.15 |
5.0 |
﹢0/-0.30 |
0.37 |
330 |
+1.5 |
|
15.0 |
+0.70/+0.30 |
1.5 |
±0.15 |
5.0 |
﹢0/-0.30 |
0.40 |
330 |
+1.5 |
|
16.0 |
+0.70/+0.30 |
1.5 |
±0.15 |
5.0 |
﹢0/-0.30 |
0.40 |
330 |
+1.5 |
|
17.0 |
+0.80/+0.30 |
2.0 |
±0.20 |
6.2 |
﹢0/-0.30 |
0.47 |
330 |
+1.5 |
|
18.0 |
+0.80/+0.30 |
2.0 |
±0.20 |
6.2 |
﹢0/-0.30 |
0.50 |
330 |
+1.5 |
|
19.0 |
+0.80/+0.30 |
2.0 |
±0.20 |
6.2 |
﹢0/-0.30 |
0.50 |
330 |
+1.5 |
|
20.0 |
+0.80/+0.30 |
2.0 |
±0.20 |
6.2 |
﹢0/-0.40 |
0.50 |
330 |
+1.5 |
|
21.0 |
+0.80/+0.30 |
2.0 |
±0.20 |
6.2 |
﹢0/-0.40 |
0.50 |
330 |
+1.5 |
|
22.0 |
+0.80/+0.30 |
2.0 |
±0.20 |
6.2 |
﹢0/-0.40 |
0.50 |
330 |
+1.5 |
|
23.0 |
+0.80/+0.30 |
2.0 |
±0.20 |
7.5 |
﹢0/-0.40 |
0.50 |
330 |
+1.5 |
|
24.0 |
+0.80/+0.30 |
2.0 |
±0.20 |
7.5 |
﹢0/-0.50 |
0.50 |
330 |
+1.5 |
|
25.0 |
+0.80/+0.30 |
2.0 |
±0.20 |
7.5 |
﹢0/-0.50 |
0.50 |
330 |
+1.5 |
|
26.0 |
+0.80/+0.30 |
2.0 |
±0.20 |
7.5 |
﹢0/-0.50 |
0.50 |
330 |
+1.5 |
在线联系供应商
Other supplier products
 |
Progressive Die/Punching Die | Introduction Tungsten carbide material is widely used in area where high wear resistance is required ,for example in drawing die, to draw copp... |
 |
Carbide Strip | Carbide strip, widely applied in woodworking and stone working. The grade selection is very important, hard grades can last a longer lifetime, howe... |
 |
Sintering HIP Furnace | IntroductionBase on years' experience and professional in manufacturing tungsten carbide materials, Toonney sintering furnace plant improves curren... |
 |
Cemented Carbide Die | Introduction of Heading Die The application in cold heading die area is one of the main applications of tungsten carbide material. Heading die... |
 |
Sintering Furnance | IntroductionBase on years' experience and professional in manufacturing tungsten carbide materials, Toonney sintering furnace plant improves curren... |
Same products
 |
The Ultimate Tool for Bubble-Free Displays | 卖方: 深圳市维客修科技有限公司 | FORWARD FW-16R除泡机、FW-8R迷你除泡机，在手机、iPhone、iPad、平板屏幕翻新过程中，去除屏幕OCA气泡，最大支持12.9寸屏幕。安全门设计，24V低压风阀配置，有效降低... |
 |
Precision CNC Lathe With Conjoined Oblique Rail Cutter Tower | 卖方: Zhejiang Guoyu CNC Machine Tool Co., Ltd. | Technical Characteristics: 45° slant bed base structure, with strict aging treatment, smooth ... |
 |
Rail Welder A Frame aligners railway welding tools | 卖方: 834406 | 产品描述 A型车架 A-Frame 是一种导轨对准器，可精确对准要焊接的导轨。该设备在焊接操作期间将导轨固定到位。 |
 |
2 parts fluid mixing dispenser 2 component dosing epoxy PU silicon rubber vacuum system | 卖方: 824681 | What is the difference between 2K AB adhesive materials manual potting machine and robot pottingm... |
 |
Horizontal Machining Center | 卖方: Xilong (Shanghai) Machine Tool Co., Ltd. | Horizontal Machining Center parts can automatically finish four sides milling, boring, drilling, ... |
