Shock test Chamber

• 

Thermal shock test chambers are classified as 2-chamber dynamic shock and 3-chamber static shock. They can be used in thermal shock test as well as the high-temperature or low-temperature test. They are applicable for the applicability test of the sample products in aerospace, aviation, military industry, electronics and electrics under the condition of drastic temperature change and the safety and reliability test for the electronic elements and parts as well as the selection of products

Specs & Technical Parameters 3TS-100 3TS-210 3TS -300 3TS -500
Pre-heat room Upper limit preheat temperature 200℃
Heating time R.T.～＋200℃, about 40min (unload)
Pre-cool room Lower limit precool temperature -75℃
Cooling time R.T.～-70℃, about 90min（unload）
Workroom Temperature shock range -20℃、-40℃、-55℃～＋150℃
Temperature fluctuation ≤±0.5℃
Temperature deviation ≤±3℃
Transform time ≤15S
Temperature revert time ≤5min
Temperature revert conditions 3CJ-100S sample load: 10kg Sample exposed
3CJ-210S sample load: 15kg 30min in 150℃,
3CJ-300S sample load: 25kg 5min in ambient temp.
3CJ-500S sample load: 35kg 30min in -55℃,
Capacity 100 L 210 L 300 L 500 L
Workroom dimensions (cm) D 50 70 70 90
W 50 60 78 80
H 40 50 55 70
Exterior dimensions (cm) D 115 135 135 250
W 195 210 225 225
H 210 220 230 215
Built-in 2 layers stainless steel plate, independent over-temperature protection, accumulated calculagraph, halogen
Model TS-162 TS-340 TS-500 TS-1000
Workroom dimensions (cm) 45*45*45 60*60*60 80*80*80 100*100*100
Exterior dimensions (cm) 156*87*154.5 171*102*184.5 191*122*226.5 211*142*266.5
Sample zone dimensions 30*30*25 45*45*36 65*65*50 85*85*70
Temperature range A:-20℃~200℃ B:-40℃~200℃ C:-60℃~200℃
Temperature fluctuation ≤±2℃ for high temperature and low temperature
Temperature fluctuation ≤±0.5℃ (under constant temperature)
Sample zone load 20kg 30kg 50kg 60kg
■ Structure characteristics

1.Equipment structure takes up stainless steel plate plus (41090) power for hull painting. It not only has good profile, but also has fine corrosion resistance.
2.It utilizes imported closed-type compressor unit imported from Europe and USA, which has solid and durable structure and is endurable and can greatly enhance service property and life of the equipment; it takes up advanced energy-saving design, which can save electric power by 30%, save water by 20%, and it uses HFC refrigerant that will not harm human body and nature, you can conduct test in safe way;
3.It has advanced and innovative control theory, it integrates three control systems of PLC, HMI and SOC in fine way. Control is correct by 100%, and you can experience the novel control feeling;
4.It utilizes most powerful and reliable PLC and special modules in the industry circle. 50 programs and 2500 steps are provided for user to make setting/storage and running;
5.It utilizes protection module for safe voltage, the withstand voltage can reach 500V. After energizing the equipment, the equipment will not be burned and it can protect the equipment by 100%.
6.It takes up high-sense FastAIT monitoring and refrigerating system imported and achieves effective control and management for refrigerant volume;
7.It has automatic safety protection switch, which has high sensitivity, can detect any state, cut off protection and give alarm in shortest time and assure safety of the personnel and equipment;
8It utilizes the advanced USB storage device in the industry. It is the only one for using the USB interface for storing data. It has not only large storage capacity and fast transmission rate, but also is portable, has great supporting property and is convenient.;
9.It can separately raise temperature, reduce temperature, humidify and dehumidify, it utilizes unique BTHC flat constant temperature and humidity regulating mode;
10.The radio tele-monitoring system takes up IPC/SCADA architecture LAN network interface, it can connect to more than 200 equipments at the same time, and it can avoid the complex wiring and eliminate the regional limit;
11.It has air supply and circulating system, which can avoid dead angle of air flow in the chamber and improve the uniformity degree of product temperature and humidity.
constitute
Inner chamber material: stainless steel plate Shell material: Stainless steel with texture treatment or high-quality cold rolled steel plate with static injection
Thermal-insulating material: high-density isocyanurate foam + glass fiber
Cable hole: inside diameter of Φ50, Φ80 , Φ100…
Heater: Nichrome electric heater
Mixing blower: centrifugal blower
Motor: condenser type
Castor: 4 active castors with braking
Observation window: built-in toughened glass in heating unit
■Refrigerating system
Refrigerant: environment-friendly R404 and R232 refrigerant
closed-type and low-noise rotor compressor imported from Europe and USA
Refrigeration mode: machinery compression single-step refrigeration (air-cooled condenser) and machinery compression dual cascade system refrigeration (air-cooled condenser)
R404 and R232 refrigerant: environmental protection refrigerants
■Control system:
TEMI880 touch-type temperature and humidity programmable controller
Operating interface: LED display
Temperature and humidity controller: touch-type LED controller
Setting mode: touching type
Running mode: setting-up running and programmed running
Program: 100 groups in 1000 sections
Resolution: temperature: ± 0.1 ℃; humidity: ± 1%RH
Input: platinum thermal resistance
Control mode: PID control
Communication function: LAN network interface
Additional function: alarm and display function, power-off protection function, upper limit temperature alarm function, timing function (auto startup and auto stop), self-diagnosis function, curve record and display function, paperless record, USB data export, tele-monitoring and so on.
It can execute 100 STEP X 10 PATTEM mode.
Each section can be grouped and executed in crossing way.
The execution time for each section can be set up between 0-999H plus 59min.
For setting up for each group, it can circulate within 1-999 in part or entirely for option.
In execution, it can select group circle picture or section execution picture and can know the remaining time for execution.
It has power-off function. After power recovery, it can complete the remained test.
It can select single-section control or multi-section programmable control.
The screen has backlight time control function and it can adjust the backlight brightness.
For executing single-section control, it can change the execution value at will. The memory-type multi-function control has automatic control output functions, such as heating heater and humidifying heater for electromechanical solenoid valve for different groups of refrigerating compressors and so on.
■Safety device
Humidifier dry-combustion protection, independent over-temperature protection, water shortage protection, over-current protection, refrigerant high-pressure protection switch, over-current circuit breaker, earth leakage protection and so on.
■Operation ambient temperature: ＋5℃～＋ 30℃
■Power supply：AC220±10%V 50±0.5Hz single-phase double-wire + protective grounding wire/ AC380±10%V 50±0.5Hz three-phase four-wire+ protective grounding wire
■Accessory
1 cable hole (Φ50, Φ80 , Φ100…) cover, 2 sets of shelf, 2 protector tubes, 1 overflow water tube, 1 copy of operating specification
■Optional accessory:
recorder, tele-monitoring software
Note:
1. The products above can be customized according to demands of the clients;
2.The technical parameters above are the data obtained under room temperature of 20℃ and non-load condition.

Other supplier products

	Salt spray corrosion test chamber	This product series can simulate the marine climate and can be used to test the salt fog resistant performance of materials, products and their coa...
	Temperature & humidity test chamber	This product series is widely used in the temperature variation tests, cold resistance tests and storage with low-temperature in the fields of aero...
	Shock test Chamber	Thermal shock test chambers are classified as 2-chamber dynamic shock and 3-chamber static shock. They can be used in thermal shock test as well as...
	Dust Ingress Chambers	This product is applicable for the dust proof and resistant test of various auto components and parts including lamps, meters, electric dust proof ...
	Ozone climatic test chamber	This series is applicable for the aging cracking test of non-metal materials and rubber products. Model OC-100 OC-250 OC-500 OC-010 Workroom dime...

Same products

	Small waste incinerator. Beach garbage incineration	Seller: Hangzhou Fire Print Technology Co., Ltd.	Green waste incinerator can be customized: Content product: 5 cubic meters, 2 tons of garbage dis...
	Strong disinfection and sterilization equipment for classrooms	Seller: Hangzhou Fire Print Technology Co., Ltd.	Space disinfection equipment Strong disinfection and sterilization equipment for classrooms Power...
	Machining	Seller: Hebei Jinganruineng Environmental Science & Technology Co., Ltd	Machining Product description: Our company has a variety of large-scale machining equipment a...
	Enamelled Steel Plate	Seller: Hebei Jinganruineng Environmental Science & Technology Co., Ltd	Enamelled Steel Plate Product description: Enamel assembly tank is made of enamel steel pla...
	Gas Holder	Seller: Hebei Jinganruineng Environmental Science & Technology Co., Ltd	Gas Holder Product description: We take use of corrosion - resistant, high - strength membr...