ABS Plastic Injection Mold 49443

Brief Introduction of Hanking ABS molds

Mould Name: Plastic Injection ABS Molds

Part Material: ABS

Product Size: 172*123 mm

Product Description: clear window

Mould Cavity: 1 Cavity

Mould Size: 300*380*250 mm

Mould Cavity Steel: ASSAB 8407

Mould Injection System: hot runner

Mould Ejection System: Round ejector

Mould Cycle Time: 38s

Mould Life Cycle: 500,000

Lead Time: 42 working days

Mold export to: Europe

For ABS plastic part molds, HanKing will make good plastic injection mold design from wall thickness, draft angle, venting, ejector system, balance and a good runner.

Design for ABS Plastic Injection Molds

The wall thickness of the product is related to the flow length of the melt, production efficiency, and use requirements. The ratio of the maximum flow length of the ABS melt to the wall thickness of the product is about 190:1. This value will vary depending on the grade. Therefore, the wall thickness of the ABS product should not be too thin. For products has electroplating requirement, the wall thickness should be slightly thicker to increase the adhesion of the coating to the surface of the article. For this purpose, the wall thickness of the product is preferably between 1.5 and 4.5 mm.

When considering the wall thickness of the product, we should pay attention to the uniformity of the wall thickness, do not make big difference wall thickness. For the products to be electroplated, the surface should be flat without unevenness, because these parts are difficult to remove due to static electricity, which is difficult to remove. The fastness of the coating deteriorates. In addition, the presence of sharp corners should be avoided to prevent stress concentration. Therefore, it is advisable to use arcs for transitions such as corners and thick joints.

The draft angle of the product is directly related to the shrinkage rate. Due to the different grades, the different shapes of the product and the different molding conditions, the molding shrinkage rate has a certain difference, generally 0.3~0.6%, sometimes It is 0.4~0.8%, so its product molding size accuracy is high. For the ABS product, the draft angle is considered as follows: the core portion is 31° in the demolding direction, and the cavity portion is taken 4 (/1° 20' in the stripping direction. For products with complex shapes or letters and patterns, the draft angle should be appropriately increased.

Since the products surface finish has a great influence on the electroplating performance, any slight scratch on the surface will be apparently exposed after electroplating, so that no damage is allowed on the cavity. It is also required a large effective area for ejection, good synchronization of the multiple ejector pins in the ejection process, and uniform ejection force.

In order to prevent the occurrence of poor venting in the process of filling, cause melt burning, the obvious seam line and other problems, it is required to open a vent hole or venting groove in which the depth is not more than 0.04mm, so the gas can be exhausted.

HanKing Mouldis a professional two shot moulding ltd, we provide custom plastic molding china, injection moulding, plastic plate mouldand etc. Want to know abs injection molding processor how to mold abs plastic? Please contact us.

Other supplier products

	3 Plate Mould 49113-21	Mould Name: 3 plate mould Part Material: PBT GF15 Product Size: ф34.9x82.29 Product Description: Mischschraube kpl Mould Cavity: 2 Caviti...
	Multi Cavity Mould	24 Cavities Plastic Injection Mold Product Name: 24 Cavities Plastic Injection MoldMold Base: LKM, HASCO, DME, etc.Mold Steel: NAK80, ASSAB8407, S1...
	Plastic Insert Mold 139-86	Mould Name: Plastic Insert Mold Part Material: PA + Glassfiber Product Size: 11*30*1.3 Product Description: Stator Mould Cavity: 4 Cavities Mo...
	Prototype Mould	As a tool supplier whose goal is becoming an expert in the industry, Hanking Moldhas experience in handling many different types of mould, includin...
	Adapter Charger Housing Mold 496-1	Mould Name: Adapter Charger Housing Mould Part Material: PC Product Size: 58.3*57.9*8.6mm Product Description: Adapter Charger Housing UK Mould Cav...

All supplier products

Same products

	Washable Cheap 13.56Mhz 213 Nfc Mini Stickers 13.56 Mhz RFID Label Sticker Tag HF/UHF Tags Dry Inlay	Seller: XIUCHENG RFID	Size：On request Material:PET, PVC,paper or customized Frequency:UHF/HF Printing:Thermal transf...
	Micronized wax used for industrial paint processing	Seller: Syntop chemical Co.,Ltd.	Micronized wax is a vital functional additive in industrial paint processing, with primary functi...
	Plant Growth Regulator Manufacturer	Seller: HEBEI LAIKE BIOTECH CO.LTD	Plant Growth Regulator Manufacturer Plant Growth Regulator Manufacturer - Laike Biotech spec...
	Fungicide Supplier	Seller: HEBEI LAIKE BIOTECH CO.LTD	Fungicide Supplier Wholesale Fungicide - Laike Biotech is a professional supplier and manufa...
	Fungicide Supplier	Seller: HEBEI LAIKE BIOTECH CO.LTD	Fungicide Supplier Wholesale Fungicide - Laike Biotech is a professional supplier and manufa...