ATE-2 LED Driver Automatic Test System
ATE-2 LED driver automatic test system is applied to the production line for the finished products testing. With features of simplified operation and nice-looking, the workers can operate it at very short time. This system can meet the requirements of IEC62384, GB24825-2009 and other relative standards.
Characteristics:
•This equipment adopts the special designed electronic load to imitate the V-I curve of LED.
•The normal LED driver has the disadvantage of high ripple, so it will have big deviation when it drives the traditional electronic load. For this equipment, the electronic load is update, so that to approach the real LED load.
•This system contains a programmable frequency conversion power supply to ensure fast switch and choose the input voltage and frequency of tested driver.
•The test equipments, electronic load and programmable frequency conversion power supply in this system are special developed and designed to meet the LED driver test requirements.
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection.
•It can test 4 LED drivers input and output at one time.
•The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer.
•Enable to print out the series number and parameters of sub-quality products by working with a micro-printer,
•Enable to achieve the barcode record function by working with a barcode scanner.
•The test report can be saved as Excel file for consult, statistic and analysis purpose.
•Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.
System function:
•Low voltage test and surge current test:
Full-load test includes:
Input: Voltage, current, power, power factor, frequency, harmonic and 2 to 11 times harmonic component
Output: voltage, current, power, ripple wave, efficiency
Steady state test includes:
Steady state 1, steady state 2, steady state 3. The chopped wave of power (enable to test dimming lights), voltage, and frequency in each state can be set separately; the other parameters are same as the full-load test.
Linear adjustment rate test; load adjustment rate test
•Over output voltage (current) protection test, under output voltage (current) protection test
•Output shorten circuit protection test, output open circuit protection test
•Stabilization time test; cut off time test
•Capacity discharge function
•Barcode record function
Specifications:
| Item | Test Range | Tolerance | Test Condition |
| Voltage | AC: 3～300V (CF=1.67) | ±(0.1%reading+0.1%range+1digit) |
45~65Hz sine-wave |
| DC: 3～500V | |||
| Current | AC: 5mA～2.7A (CF=3) | ||
| DC: 5mA～8A | |||
| Power | AC: 0.015～800W | ||
| DC: 0.015～4000W | |||
| Power Factor | 0.000～1.000 | ±(0.002+0.001/reading+1digit) | |
| Frequency | 45Hz～65Hz | ±0.1% Reading | |
| Harmonic | Total harmonic, and 2-11 times harmonic component | ±(0.1% range+5% Reading) | |
| Surge Current | 50mA～100A | ±(0.5% range+0.5% range+1digit) | Square wave with pulse width greater than 10 10μs Calibration validity: 12month |
| Lamp Voltage | AC: 3～300V (CF=1.67) | ±(0.1%reading+0.1%range+1digit) | 45~65Hz sine-wave Calibration validity: 12moths |
| DC: 3～500V | |||
| Lamp Current | AC: 5mA~2.7A (CF=3) | ||
| DC: 5mA～8A | |||
| Lamp Power | AC: 0.015～800W | ||
| DC: 0.015～4000W | |||
| Ripple Current | Max: 5mA～8A | ±(1%reading+1%range) | 20-70kHz sine-wave |
Note:
•Fundamental harmonic of voltage, current, lamp voltage, lamp current (AC) is 45Hz~65Hz. Frequency range is 45Hz~1MHz
•The frequency range of ripple current is 45Hz~1MHz.
you may surf our website of our company to get more information in here:
Send product request
Other supplier products
 |
IS-*M**P Integrating Sphere with Side Assistant Opening | The integrating sphere works with a Spectrophotometer to do the photometry, colorimetry and radiometry parameters measurement, but the large size o... |
 |
LSG-1600 Type C Goniophotometer | LSG-1600 Type C Goniophotometer is an automatic goniophotometric measurement system for measuring photometric parameters of luminaires, such as LED... |
|
|
ATE-2 LED Driver Automatic Test System | ATE-2 LED driver automatic test system is applied to the production line for the finished products testing. With features of simplified operation a... |
 |
LEDLM-80PL LED Optical Aging Test Instrument | The LED Optical Maintance and Life Test System (LEDLM-80PL) is according to IES LM-79, IES LM-80, IES LM-82, TM-12, GB2312-80, CIE and IEC Standard... |
 |
LSG-1800B High Precision Rotation Luminaire Goniophotometer | LSG-1800B Goniophotometer is high precision automatic goniophotometric instrument for luminous intensity distribution measurements with facility fo... |
Same products
 |
China GT-JYH12 Hot Runner Shrinking Machine(CNC) | Seller: Zhaoqing City Greater Technology Co., Ltd | * Description GT-JYH12 Hot Runner Shrinking Machine is a shrinking machine mainly for hot runner... |
 |
China GT-JY18 18 Station Shrinking Machine | Seller: Zhaoqing City Greater Technology Co., Ltd | * Description GT-JY18 18 Staion Shrinking Machine is one popular tubular heater shrinking machin... |
 |
Multiple Blades Digital Label Cutter VR350 | Seller: WILLIAM CNC TECHNOLOGY | Multiple Blades Digital Label Cutter VR350 The VICUT multiple blades digital die cutterVR350, eq... |
 |
Digital Label Die Cutting Machine VR240X | Seller: WILLIAM CNC TECHNOLOGY | Digital Label Die Cutting Machine VR240X VR240X digital label finisheris redeveloped based on th... |
 |
Rotary die cutting machine VR320 | Seller: WILLIAM CNC TECHNOLOGY | Rotary die cutting machine VR320 The VICUT VR320 roll to roll labels cutting machineis the most ... |
