ATE-2 驱动自动测试系统

ATE-2 LED driver automatic test system is applied to the production line for the finished products testing. With features of simplified operation and nice-looking, the workers can operate it at very short time. This system can meet the requirements of IEC62384, GB24825-2009 and other relative standards.

Characteristics:
•This equipment adopts the special designed electronic load to imitate the V-I curve of LED.
•The normal LED driver has the disadvantage of high ripple, so it will have big deviation when it drives the traditional electronic load. For this equipment, the electronic load is update, so that to approach the real LED load.
•This system contains a programmable frequency conversion power supply to ensure fast switch and choose the input voltage and frequency of tested driver.
•The test equipments, electronic load and programmable frequency conversion power supply in this system are special developed and designed to meet the LED driver test requirements.
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection.
•It can test 4 LED drivers input and output at one time.
•The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer.
•Enable to print out the series number and parameters of sub-quality products by working with a micro-printer,
•Enable to achieve the barcode record function by working with a barcode scanner.
•The test report can be saved as Excel file for consult, statistic and analysis purpose.
•Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.

System function:
•Low voltage test and surge current test:
Full-load test includes:
Input: Voltage, current, power, power factor, frequency, harmonic and 2 to 11 times harmonic component
Output: voltage, current, power, ripple wave, efficiency
Steady state test includes:
Steady state 1, steady state 2, steady state 3. The chopped wave of power (enable to test dimming lights), voltage, and frequency in each state can be set separately; the other parameters are same as the full-load test.
Linear adjustment rate test; load adjustment rate test
•Over output voltage (current) protection test, under output voltage (current) protection test
•Output shorten circuit protection test, output open circuit protection test
•Stabilization time test; cut off time test
•Capacity discharge function
•Barcode record function

Specifications:

Item	Test Range	Tolerance	Test Condition
Voltage	AC: 3～300V (CF=1.67)	±(0.1%reading+0.1%range+1digit)	45~65Hz sine-wave Calibration validity: 12 month
	DC: 3～500V
Current	AC: 5mA～2.7A (CF=3)
	DC: 5mA～8A
Power	AC: 0.015～800W
	DC: 0.015～4000W
Power Factor	0.000～1.000	±(0.002+0.001/reading+1digit)
Frequency	45Hz～65Hz	±0.1% Reading
Harmonic	Total harmonic, and 2-11 times harmonic component	±(0.1% range+5% Reading)
Surge Current	50mA～100A	±(0.5% range+0.5% range+1digit)	Square wave with pulse width greater than 10 10μs Calibration validity: 12month
Lamp Voltage	AC: 3～300V (CF=1.67)	±(0.1%reading+0.1%range+1digit)	45~65Hz sine-wave Calibration validity: 12moths
	DC: 3～500V
Lamp Current	AC: 5mA~2.7A (CF=3)
	DC: 5mA～8A
Lamp Power	AC: 0.015～800W
	DC: 0.015～4000W
Ripple Current	Max: 5mA～8A	±(1%reading+1%range)	20-70kHz sine-wave

Note:
•Fundamental harmonic of voltage, current, lamp voltage, lamp current (AC) is 45Hz~65Hz. Frequency range is 45Hz~1MHz
•The frequency range of ripple current is 45Hz~1MHz.

you may surf our website of our company to get more information in here:

Other supplier products

	IS-*M**P 测光积分球	IS-*M测光积分球，适用于节能灯、白炽灯、冷阴极灯、卤钨灯、直管形荧光灯、环形荧光灯、大功率直管形荧光灯、HID灯等光源光色电测试。 积分球尺寸可以根据顾客需求定制 直径：1.5m、1.75m、2.0m、2.5m、3.0m you may surf our website of our c...
	ATE-2 驱动自动测试系统	ATE-2 LED driver automatic test system is applied to the production line for the finished products testing. With features of simplified operation a...
	LPCE-1 CFL&LED高精度快速光色电综合测试系统	产品简介： LPCE-1系统适用于节能灯、卤素灯、银光灯、HID、CCFL以及LED等各类光源的对于光色电参数的检测。主机（LMS-5000光谱仪）是一款应用非常广泛的光谱仪，保持传统高精度机械扫描方式的同时大大提高了测试速度，380nm-800nm全波段扫描仅需10S。采用标准RS-232通...
	LSG-2000 旋转反光镜立式分布式光度计	LSG-2000是一款自动测试3D光强分布曲线的旋转反光镜立式分布光度计系统， 可实现C-γ、A-α和B-β测量方案，完全满足CIE，IESNA，GB等国际国内标准。 产品简介： 根据LM-79条款9.3.1，只有两种分布光度计是被认可的，即中心旋转反光镜式分...
	LEDLM-80PL LED老化寿命测试系统	The LED Optical Maintance and Life Test System (LEDLM-80PL) is according to IES LM-79, IES LM-80, IES LM-82, TM-12, GB2312-80, CIE and IEC Standard...

供应产品

Same products

	Step Drill	卖方: SINOLITE TOOLS LTD.	Step Drill Step Drill Bits | Step Drill Bit Set Supplier & Wholesale Step drill bitsare a s...
	Twist Drill	卖方: SINOLITE TOOLS LTD.	Twist Drill Precision Twist Drill Bits | HSS, Cobalt & Carbide Drills Precision twist drill...
	Metal Cutting Tools	卖方: SINOLITE TOOLS LTD.	Metal Cutting Tools Metal Cutting Power Tools & Cutting Tools for Metal | Sinolite Looking ...
	Taper Shank Drill	卖方: SINOLITE TOOLS LTD.	Taper Shank Drill Taper Shank Drill Bits | HSS Taper Shank Drills Supplier Taper shank drill bi...
	Traditional Welding in Furniture Manufacturing	卖方: Traditional Welding in Furniture Manufacturing	Traditional Welding in Furniture Manufacturing Pain Points of Traditional welding operat...