Marine Loading Arm
Marine Loading Arm
Product Details
MARINE LOAGING ARM
Marine loading arm is designed for fluid transport between terminal and tanker pipeline system of liquid or gaseous state one kind of product.
If you need Tower Type Gangway, quick release hook, pillar gangwayand marine loading arm, welcome to contact us.
Our company design and manufacture of Marine oil arm in the process of transmission,within the scope of normal trough boat drift with the tank ship linkage. Range through the monitoring system in the tank when the ship manifold drift out of the scope of work provides audible and visual alarm. And equipped with emergency escape system implementation under the condition of loading arm emergency escape and hull.
numbermodelOn the behalf of contentspecification
1AMMarine loading arm
26Six rotary joint
33Double-barrelled
1--self-supporting marine loadin g arm
3--independent support marine
loading arm
4--independent support marine lo ading arm (Double-barrelled)
4HHydraulic control
M-manual
H-hydraulic driven
5300
Caliber 300mm
AM63 marine loading arm
Basic Features: Material:
Easy operation Carbon steel
Easy seal change Stainless steel
Small dead weight Low-temp steel
Minimal wind loads Lined steel, etc
Separate support structure Nominal diameter:
Uniform diameter DN80 to DN600
Long reach capability
The model features a separate support structure with its own generously aized mechanical bearings. Which take up all major external loads and memets.
The model had been developed especially to meet the increased requirements for loading critical media. furthermore,the model can be designed for long reach capability.
The model can be equipped with emergency release coupler(ERC) and/or quick connect/disconnect coupler(QCDC)
FEATURES
The swivels and pipe are only subjected to stress by internal pressure and weight.
Generously sized bearings at supporter minimizefriction and facilitate easy operation.
The diameter of swivel and pipe is uniform throughout.
ALL swivels are identical thus considerably reducing the spares requirements.
Line is attached to supporter by means of special mounts which also compensate for thermal expansion due to temperature variations to overstressing.
Balance the arm in all positions by meansof counterweights.
Balance inboard and outboard arm by a moving counterweight.
ACCESSORIES
Hydraulic drive assemblies
Drain connecters
Vacuum breaker and/or N2 purge system
Electrical stray current protection
Safety ladders
Adjustable support jack
Insulation flange
Range limit system
Shut-off valve
Emergency release coupler(ERC)
Quick connect/disconnect coupler(QCDC)
Vapour return line, steam line etc.
Connection area
The connection area is that volume in space in which the loading arm should be connected to the ship's flange. The area results the min./max.mainflod setback and sizes of vessel(fully laden of light)at low or high tide.
Working area
In the area the ship's flange connection can move freely and without danger during loading/unloading.
Warning area
Operating personnel will be warned by audio/vosial alarms product valves on the land and ship side should be closed to interrupt product transfer.
Emergency release area
The emergency release area is required ti actiovate and complete separation of the arm form the tanker manifold.
Emergency release coupler (option)
Emergency release coupler is composed of double ball valve or double butterfly valve,it is installed in the straight pipe on the top of loading arm's three-dimensional joint,when loading arm is on working,it will work in the following situation:
lWhen there is a fire,the operator can't close
lGust caused intense drift of the ship
lDrift is too large,the operator can't close
Emergency release coupler will escape,before it escapes,it will close the pipeline on the ship side and the shore side in the same time to make sure that media does not leak.
Manual,hydraulic driven QCDC（option）
It is installed in the flange which is docked with loading arm and ship,its characteristic is that it doesn't have to use special tools.Its jaw can join the loading arm's flange and ship's flange together quickly,so it can save manpower and material resources effectively.
Send product request
Other supplier products
 |
AL2404 loading arm | AL2404 loading arm Product Details Model:AL2404 Bottom loading arm Loading Arm, Upper Loading Arm, Bottom Loading Arm Company. Suitable occa... |
 |
Quantitative Loading System | Quantitative Loading System Product Details QUANTITATIVE LOADING CONTROLLER SYSTEM CHK-AX series quantitative loading controller is intelligent ... |
 |
LNG loading arm | LNG loading arm Product Details After the LNG ship berths at the dock, the LNG loading arm will connect the unloading line on the ship and the ... |
 |
Quantitative Loading System | Quantitative Loading System Product Details QUANTITATIVE LOADING CONTROLLER SYSTEM CHK-AX series quantitative loading controller is intelligent ... |
 |
LNG loading arm | LNG loading arm Product Details After the LNG ship berths at the dock, the LNG loading arm will connect the unloading line on the ship and the ... |
Same products
 |
Hydraulic rail tensor for track maintenance / Factory Rail machine supplier | Seller: Wuhan linkage track equipment | Hydraulic rail tensor rail puller Hydraulic Rail Puller Rail Tensor It’s suitable for rail ... |
 |
GREENMAX EPP Granulator | Seller: INTCO Recycling | Production automation, manpower saving. Perfect adaption to multiple materials processing system.... |
 |
GREENMAX Washing Line T-EPS Food Trays | Seller: INTCO Recycling | GREENMAX Washing Line T-EPS Food Trays is specially used for EPS recycling system of EPS food tra... |
 |
GREENMAX Styrofoam shredder | Seller: INTCO Recycling | Shredding is the first process to deal with plastic waste. GREENMAX Rhea Shredder is a cutting te... |
 |
GREENMAX Washing line Triton Series | Seller: INTCO Recycling | GREENMAX Triton Series Washing System is mainly used for cleaning recycled waste plastic products... |
