100G QSFP28 SR4 100M
The qsfp28 100gbase sr4 module is a highly integrated 4x25G transceiver focused on reach, bandwidth, density and cost for high port-count 100G systems, and client-side 100G interfaces. Each lane can operate at 25Gbps up to 70m using OM3 fiber or 100m using OM4 fiber. These modules are designed to operate over multimode fiber systems using a nominal wavelength of 850nm. The electrical interface uses a 38-contact edge type connector. The optical interface uses a 12-fiber MTP/MPO connector.
Features of QSFP28 100G SR4 100m
4 channels full-duplex transceiver modules
Transmission data rate up to 25Gbps per channel
4 channels 850nm VCSEL array
4 channels PIN photo detector array
Hot-pluggable QSFP28 form factor
Maximum link length of 70m on OM3 Multimode Fiber(MMF) and 100m on OM4 MMF
Single 1X12 MPO connector receptacle Hot-pluggable electrical interface
0–70°C operating temp
Low power consumption < 2.5W
RoHS6 compliant (lead-free)
Applications of QSFP28 SR4 100m
100GBASE-SR4 100G Ethernet
Specifications of QSFP28 100G SR4 100m
Recommended Operating Environment
Optical Transmitter Performance
Optical Receiver Performance
Recommended Operating Environment specifies parameters for which the electrical and optical characteristics hold unless otherwise noted.
Pin Definition of QSFP28 100G SR4 100m
Important Notice of QSFP28 100G SR4 100m
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by T&S before they become applicable to any particular order or contract. In accordance with the T&S policy of continuous improvement specifications may change without notice.
The publication of information in this data sheet does not imply freedom from patent or other protective rights of T&S or others. Further details are available from any T&S sales representative.
If you want to know more kinds of optical communications products, please visit our website.
Other supplier products
|
|
FIBER PATCHCORD & PIGTAIL |
patch cord pigtailnormally consists of optical fiber cable and connectors at both ends of the cable, the pigtail is connector assembled at one end，... |
|
|
100G QSFP28 DIRECT ATTACH CABLE |
QSFP28 Direct Attach Cables are compliant with the SFF-8665 specifications. Various choices of wire gauge are available from 30 to 26 AWG with vari... |
|
|
MTP®/MPO Shuffle Cable |
Like MTP®/MPO cable, MTP®/MPO Shuffle cableis also used for connecting MTP® modules together as a permanent link, and it also be used w... |
|
|
FBG Strain Sensor |
ES-01 sensor measures the strain by utilizing the inherent feature of strain-sensitivity of FBG. The sensor fits to be embedded to measure the stra... |
|
|
MT FERRULE |
The MT ferruleis a multi-fiber, plastic ferrule with a square end-face of 6.4x2.5 mm and fiber pitch 0.25mm, widely applied in MPO connectors and A... |
All supplier products
Same products
|
|
SFP28 25G LR |
Seller: T&S COMMUNICATIONS CO., LTD. |
T&S TSSP-3125G-LR is a single-Channel, Pluggable, Fiber-Optical SFP28 for 25 Gigabit Ethernet... |
|
|
SFP 10G LR |
Seller: T&S COMMUNICATIONS CO., LTD. |
T&S TSPP-31192-LR is a Series single-mode, Pluggable Fiber-Optical SFP for 10G Ethernet, comp... |
|
|
SC/SM/PC |
Seller: T&S COMMUNICATIONS CO., LTD. |
ID 0.125/0.126mm, concentricity 1.0um, OD 2.4990mm, this kind of standard optical ferrules with g... |
|
|
LC/SC LOOPBACK |
Seller: T&S COMMUNICATIONS CO., LTD. |
LC or SC loopback or other customized, SM and MM fiber type for option, optical information routi... |
|
|
IP LC/SC FIBER CABLE |
Seller: T&S COMMUNICATIONS CO., LTD. |
The IP connector together with supported cable is applied to 4G,5G, Base Station remote radios, a... |
