100G QSFP28 SR4 100M
The qsfp28 100gbase sr4 module is a highly integrated 4x25G transceiver focused on reach, bandwidth, density and cost for high port-count 100G systems, and client-side 100G interfaces. Each lane can operate at 25Gbps up to 70m using OM3 fiber or 100m using OM4 fiber. These modules are designed to operate over multimode fiber systems using a nominal wavelength of 850nm. The electrical interface uses a 38-contact edge type connector. The optical interface uses a 12-fiber MTP/MPO connector.
Features of QSFP28 100G SR4 100m
4 channels full-duplex transceiver modules
Transmission data rate up to 25Gbps per channel
4 channels 850nm VCSEL array
4 channels PIN photo detector array
Hot-pluggable QSFP28 form factor
Maximum link length of 70m on OM3 Multimode Fiber(MMF) and 100m on OM4 MMF
Single 1X12 MPO connector receptacle Hot-pluggable electrical interface
0–70°C operating temp
Low power consumption < 2.5W
RoHS6 compliant (lead-free)
Applications of QSFP28 SR4 100m
100GBASE-SR4 100G Ethernet
Specifications of QSFP28 100G SR4 100m
Recommended Operating Environment
Optical Transmitter Performance
Optical Receiver Performance
Recommended Operating Environment specifies parameters for which the electrical and optical characteristics hold unless otherwise noted.
Pin Definition of QSFP28 100G SR4 100m
Important Notice of QSFP28 100G SR4 100m
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by T&S before they become applicable to any particular order or contract. In accordance with the T&S policy of continuous improvement specifications may change without notice.
The publication of information in this data sheet does not imply freedom from patent or other protective rights of T&S or others. Further details are available from any T&S sales representative.
If you want to know more kinds of optical communications products, please visit our website.
Other supplier products
|
|
BAND SEPARATOR WDM DEVICE |
T&S BWDM 3 Ports Device is a kind of FWDM device that can separate C-band and L-band or split C-band into two parts, or split L-band into two p... |
|
|
MTP/MPO LOOPBACK |
T & S MTP / MPO fiber loop is a device used for parallel connection tests and an aging test of optical communication equipment. Well-designed b... |
|
|
AOC (ACTIVE OPTICAL CABLE) |
AOC is a cabling technology that accepts the same electrical inputs as a direct attach cable, but uses optical fiber "between the connectors". AOC ... |
|
|
STANDARD FIBER OPTIC CABLE PATCH CORD |
Fiber Patch Cord or jumper is a fiber cable that has fiber connectors terminated on one or both ends. General use of these cable assemblies include... |
|
|
FBG Temperature Sensor |
SEN-T004 Sensor measures the temperature by utilizing the inherent feature of heat-sensitivity of FBG. All the capsulation is specially designed to... |
供应产品
Same products
|
|
SFP28 25G LR |
卖方: Sumbexauto |
T&S TSSP-3125G-LR is a single-Channel, Pluggable, Fiber-Optical SFP28 for 25 Gigabit Ethernet... |
|
|
SFP 10G LR |
卖方: Sumbexauto |
T&S TSPP-31192-LR is a Series single-mode, Pluggable Fiber-Optical SFP for 10G Ethernet, comp... |
|
|
SC/SM/PC |
卖方: Sumbexauto |
ID 0.125/0.126mm, concentricity 1.0um, OD 2.4990mm, this kind of standard optical ferrules with g... |
|
|
LC/SC LOOPBACK |
卖方: Sumbexauto |
LC or SC loopback or other customized, SM and MM fiber type for option, optical information routi... |
|
|
IP LC/SC FIBER CABLE |
卖方: Sumbexauto |
The IP connector together with supported cable is applied to 4G,5G, Base Station remote radios, a... |
