.

Ignition Cable

auto ignition cableare a critical component in an internal combustion engine. They are responsible for transferring a high voltage spark from the ignition coil to the spark plugs in order to ignite the air/fuel mixture in the cylinders. Ignition cables are made of high-quality, durable materials and feature an insulated conductor to prevent short circuits. They are available in various sizes and lengths, depending on the make and model of the vehicle. spark ignition cableare essential for proper engine performance, so it is important to make sure they are in good condition before starting your engine.

How to Install Ignition Cable?

01

Connection Sequence

Remove an old wire, compare its length with the new wire, and then select the most suitable plug length, and plug it in clockwise order according to the working order of the engine.

02

Test Method

Connect the two ends of the cylinder line with the red and black probes of the multimeter. If the reading is between 1 and 20 kilo-ohm, it means that the ignition cable isn't open.

03

Matters Needing Attention

When starting the engine, if there is shaking or shooting sound, it means that the ignition cable is inserted incorrectly, and the ignition cable should be re-inserted.

How to Repair Ignition Cable?

Replacing an car spark plug cableis a relatively easy task and can be done with basic tools. Here are the steps to repair the ignition cable:

Open the hood of the car and locate the cable ignition. Depending on the make and model, the cable may be attached to the distributor cap or the coil.

Remove the old cable. Squeeze the retaining tab and gently pull the cable off.

Install the new cable. Push the cable onto the distributor cap or coil until it is secure.

Secure the cable. Tighten the retaining nut and make sure the cable is secure.

Reconnect the negative battery cable. This will prevent any electrical shorts.

Start the engine and check for proper operation. If the engine does not start, recheck the cable for a secure connection.

Replacing an car ignition cableis a simple job that can be done in just a few minutes. With the right tools and a little patience, anyone can repair the ignition cable and get their car back on the road.

How to Check Ignition Cable?

Checking the car plug cableis an important part of maintaining a vehicle. It's important to check the cable regularly to ensure it is in good condition.

First, inspect the cable visually. Make sure there are no visible signs of damage, such as fraying or cracking. Any signs of damage should be addressed immediately.

Second, check the cable for resistance. This can be done with a multimeter. Connect the multimeter leads to the cable and set the meter to measure resistance. The resistance should be between 150 and 180 ohms. If the resistance is outside of this range then the cable should be replaced.

Third, check for continuity. This can also be done with a multimeter. Set the meter to measure continuity and connect the leads to the cable. The meter should indicate the presence of a continuous circuit. If there is no continuity, then the cable should be replaced.

Finally, check the cable for any corrosion. Corrosion can be caused by moisture, which can lead to electrical problems. If any corrosion is present, the cable should be replaced.

By following these steps, you can easily check the ignition cable and ensure it is in good working condition.

Bohua, as an excellent spark plug cable factory, offers a wide range of plug cablesfor you to choose from.

Want to buy auto parts car accessories, please contact us.



Send product request

To: Foshan Bohua Auto Parts Co., Ltd
Your E-mail:
Message text:


Send to other suppliers

Other supplier products

OEM 17042-8H301 Auto Parts Fuel Pump for Nissan
OEM 17042-8H301 Auto Parts Fuel Pump for Nissan OEM 17042-8H301 Auto Parts Fuel Pumpfor Nissan The OEM 17042-8H301 Fuel Pump is a genuine Nissan part used in the car engine. It is responsible fo...
Control Arm
Control Arm China control armis a suspension component used in automobiles that connects the wheel hub and chassis. It is designed to reduce vibration and impr...
OEM 23100-4BE0A Alternators for Car for Nissan
OEM 23100-4BE0A Alternators for Car for Nissan The OEM 231004BE0Aalternator is a genuine Nissan part designed specifically for Nissan vehicles. The alternator is responsible for generating elect...
OEM  Car Fuel Filter for Toyota
OEM Car Fuel Filter for Toyota The fuel filteris used to prevent particles, water and impurities in the fuel, and ensure that the precise components of the fuel system are free f...
OEM 23300-6N200 Starter Motor for Sale for Nissan
OEM 23300-6N200 Starter Motor for Sale for Nissan The OEM 23300-6N200 starter motor for saleis a genuine Nissan part designed specifically for starting the engine in Nissan vehicles. The starter mo...
All supplier products

Same products

330037 Communication Unit Change-Over Table HS50 Original Used
330037 Communication Unit Change-Over Table HS50 Original Used Seller: Guangdong Juguangheng Automation Equipment Co.,Ltd. pantallas china brand bearing bearing supplier mobil dte 10 Reflow Wave Soldering Chain Cleaner T...
Fuel Injection Pump & Head Rotor  9443612846 for Mitsubishi Pajero 4M41 3.2L DI-D Engine
Fuel Injection Pump & Head Rotor 9443612846 for Mitsubishi Pajero 4M41 3.2L DI-D Engine Seller: CARMARY POWER CO.,LTD Fuel Injection Pump & Head Rotor 9443612846 for Mitsubishi Pajero 4M41 3.2L DI-D Engine
Seat Cushion
Seat Cushion Seller: Zhejiang Huaqi Information Technology Co., LTD Each cushion is crafted with a focus on both aesthetics and functionality. We offer a variety of ...
GF6018A CLAMP TYPE MULTIMETER CALIBRATOR
GF6018A CLAMP TYPE MULTIMETER CALIBRATOR Seller: 782364 This GF6018A high precision multi-product calibrator is compliance with national verification reg...
GF6018A CLAMP TYPE MULTIMETER CALIBRATOR
GF6018A CLAMP TYPE MULTIMETER CALIBRATOR Seller: 782364 DESCRIPTIONThe GF6018A clamp type multimeter calibrator with RS-232 port, it can be connected w...