Windshield Wiper Blades
Because of legal requirements, almost everywhere cars must be equipped with windshield wiper cutters. The windshield wiper cutter also has the characteristics of heat resistance, cold resistance, acid and alkali resistance, corrosion resistance, can fit the windshield, reducing the burden on the motor, low noise, strong water repellency, soft and does not scratch the windshield. We manufacture three types of rain wiper blades, conventional wiper blades, flat windshield wiper blades and hybrid wiper blades.
Windshield wiper cutters are consumables, and their lifespan also depends on the road conditions, environment, temperature, etc. Generally, rain wiper blade cutterare replaced in about a year, mainly depending on the frequency of use. The car owner can also clean the rain wiperblade cutter with a towel after it rains, which not only increases the service life but also protects the glass. Whether the rain wiper blade cutter can work normally or not directly affects the safety and comfort of driving, it is recommended to check and replace it regularly. For bulk conventional wiper blades, flat windshield wiper blades and hybrid wiper blades direct from MAPMS at competitive prices.
What Are the Symptoms of a Bad Windshield Wiper Blade Cutter？
The scraping is not clean and there is abnormal sound
It means that the rain wiper blade cutter arm is twisted upward. Make the wiper is stopped in the middle position and pull the wiper switch handle towards the steering wheel after the car is turned off, and then gently lift it. Wrap the rain wiper blade cutter arm with a cloth or something soft, use a wrench or pliers to clamp the wrapped part down and twist it a few times. After resetting automotive wiper system, try scratching it. The abnormal noise will be much smaller. If it is, repeat it until the abnormal noise is eliminated. If the rain wiper blade cutter arm is in the down position, it needs to be twisted in the opposite direction until the abnormal noise is eliminated.
The wiper blade
The rain wiper blade cutter is a rubber product, and it will age and harden after using it for a period of time, especially in winter Generally, wiper blades are recommended to be replaced every one to two years.
The wiper blade clean
There are articals between the wiper blade box and the windshield. When the rain wiper blade cutter is turned on, there will be a sharp sound of friction between the rain wiper blade cutter and the front windshield. In this case, you can check and clean up the articals under the wiper blade or wiper arm to keep the wiper blade clean.
Abnormal Noise
The deformation of the linkage mechanism or the influence of the motor and the gap relay, such as too fast or too slow or non-stop action, may cause abnormal noise, and due to wear, the card issuance, rust of its own mechanism, also cause to behave abnormally and so on. If it is a new rain wiper blade cutter, it is recommended to check whether there is dirt or oil stains on the windshield. It is recommended to clean the windshield with cleaning fluid or try a new one. If there is still abnormal noise, use a tool such as pliers to adjust the angle of the rain wiper blade cutter arm. However, it is recommended to go to the repair shop for special tools to adjust.
The most of common case
There is a rattling sound when the wiper wipes the windshield wiper cutter. The wrong windshield wiper cutterarm angle is the most of common case, which causes the wiper blade to jump on the windshield, resulting in abnormal noise. If the windshield wiper cutter is normal, then the angle of the wiper arm needs to be adjusted, and the wiper blade should be perpendicular to the windshield plane. Put a rag on the head of the wiper arm, then clamp it with pliers, and break it hard correctly, try to make the wiper blade perpendicular to the windshield plane.
If you need any kinds of car auto spares, please contact us, as one of the most professional auto spare parts supplier, MAPMS is willing to offer you high quality products.
Send product request
Other supplier products
 |
Ignition Coil Rubber Boots | MAPMS supplies car rubber boots for COP and pencil ignition coils, which is made of high-quality silicone, and with withstand high pressure over 40... |
 |
Components Of Cooling System | Theengine cooling systemradiates the heat generated by the combustion of the mixture in the engine combustion chamber into the air to prevent the e... |
 |
Fuel Injectors | Auto fuel injector, is a part that injects fuel into the engine cylinder. It also is a simple solenoid valve. When the solenoid coil is energized, ... |
 |
Ignition Coils | Introduction of car ignition coil Winding and potting are the key processes in the production of ignition coils. MAPMS has multiple automatic wi... |
 |
Fuel Filters | For vehicle engines, the Fuel Filterincludes Diesel Filter and Fuel Filter Diesel Filter elements mostly use filter paper, and some use felt or ... |
