Rotary Dryer
Technical Advantage:
Equipped with Spreading plate, cylinder support the two roller by tyre, the gear wheel used to prevent the cylinder axial movement, the reducer drive big gear and small gear motor, and the big gear is fixed on the cylinder, the windshield prevent the cold air into the body and the combustion chamber. Wet material with hot gas to feed the enter, in cylinder body lift up the lift plate material, make it through the heat flow and drying. Our dryer can be made according to different drying materials for the external heating and within heating. The external heating drying of charcoal, lees, coconut trees leather materials. In heating can be drying slime, sand, slag,chicken manure, cow dung and so on. Heat can use coal, gas occurrence furnace, hot air stove, gas, electric furnace.
Our dryer adopts new Spreading plate device, which has guidance, flow, material functions, it can make the material content in the dryer radial cross section to full uniform, material will become thin and all, the state of the heat flow entirely, to achieve the purpose of make full use of the heat.Our dryer choose reasonable operating parameters, coal consumption and power consumption of general baked dry machine more than 10-15%, one machine yields above 10-15%, it has been widely used. in the cement and mineral processing enterprise.
Operating principle:
Dryer heat from the combustion device, the dryer adopts whatever in heating mode. Therefore need to dry the material from feeding, the feeding slipped into the cylinder, it is spiral copy board.On the one hand the dryer tilt put material on the gravity and return flows back end, on the other hand the material being copy board over and over again, brought to the top and lift it down constantly, make the material inside the tube forming uniform curtain, and the heat flow into the line of heat exchange in the cylinder fully, because of the material and Spreading plate, contains the moisture of being drying, thus attaining the purpose of drying.
| Model(m) |
Capacity(t/h) |
Mainmotor |
Mainenginerate |
Weight(T) |
| Power(KW) |
Model |
Model |
speedratio |
| Φ1.2×10m |
2.5 |
7.5 |
Y160M-R3 |
Zl50-16-I |
-- |
13.5 |
| Φ1.5×12m |
3.3-4.9 |
10 |
Y160L-6-B3 |
JZQ500-III-2F |
-- |
18.9 |
| Φ1.5×15m |
4-6 |
18.5 |
Y200L1-6 |
JZQ500-III-2F |
-- |
21 |
| Φ1.8×12m |
4-6 |
18.5 |
Y160L-6 |
ZQ50-16II-2 |
16.46 |
23 |
| Φ2.2×12m |
7.12 |
18.5 |
Y200L7-6 |
JZQ650-III |
31.5 |
38 |
| Φ2.2×14m |
7.12 |
22 |
Y200L7-6 |
JZQ650-III |
31.5 |
40 |
| Φ2.2×16m |
12 |
30 |
Y225M-6 |
JZQ750-III |
31.5 |
45 |
| Φ2.4×14m |
12 |
30 |
Y250M-6 |
JZQ750-III |
31.5 |
51 |
| Φ2.4×18m |
10-13 |
37 |
Y250M-6 |
ZL85-13-I |
27.16 |
54 |
| Φ2.4×20m |
10-14 |
37 |
Y250M-6 |
ZL85-13-I |
27.16 |
55 |
| Φ3×20m |
25 |
55 |
Y250M-4 |
ZL100-16-I |
41.52 |
78 |
| Φ3×25m |
32-36 |
75 |
YR280M-4 |
ZL100-16-I |
41.52 |
105 |
Indirect drying parameters:
| Model Tubediameter ×Tubelength |
Inside diameter of outer shell(mm) |
Inside diameter
of inner shell（mm） |
Shell length(m) |
Shell cubage(m3) |
Shell obllqulty |
Lifting blade form |
Highest inlet air temperature(℃) |
Overall dimension |
| Φ1.5×15m Φ1.5×17m Φ1.5×19m |
1500 |
500 |
15 17 19 |
20.27 22.97 25.68 |
3-5% |
Up-lift |
850 |
16.2×2.7×2.7 18.2×2.7×2.7 20.0×2.9×2.9 |
| Φ1.8×21m Φ1.8×23m Φ1.8×25m |
1800 |
650 |
21 23 25 |
35.91 39.33 42.75 |
3-5% |
Up-lift |
850 |
22.5×2.7×2.7 24.5×2.9×2.9 26.5×2.9×2.9 |
| Φ2.2×21m Φ2.2×23m Φ2.2×25m |
2200 |
800 |
21 23 25 |
58.10 63.61 69.15 |
3-5% |
Up-lift |
850 |
-- |
Other supplier products
|
|
Belt Conveyor |
1.High throughput and great adaptabilityThe different model basically meet the customer requirements of different throughput. Belt conveyor can be ... |
|
|
Vibrating Feeder |
1.High efficiency and low operation costAdopts double eccentric shaft as excitation source, amplitude stable, making sure the vibration ore materia... |
|
|
Superfine Micronizer |
Brief introduction：Ultrafine powder mill is world leading fine powder grinding equipment, adopt dry processing to make powder, suitable for process... |
|
|
Shaking Table |
Product advantage:Shaker is a combination of the internal shaking and mineral processing technology of gravity, high enrichment ratio, sorting effi... |
|
|
Jaw Crusher |
1.Good stability, high reliabilityMoving jaw Assembly adopts the high quality casting components,heavy eccentric axis also forging billets for proc... |
All supplier products
Same products
