Low speed centrifuge

1. If the glass tube breaks during the centrifugation process, the centrifuge cavity, the interior of the casing and the surrounding debris must be removed; otherwise, the centrifuge will be damaged. A layer of Vaseline can be applied to the top of the centrifuge chamber and the rotor can run without load for a few minutes. The dirt can be easily removed by mixing it with Vaseline. 2. Use a neutral detergent such as soapy water to clean dust and residual samples from the centrifuge, but toxic and radioactive materials must be specially treated. If it is found that the rotor is corroded and cracked, it should be replaced immediately. It is also necessary to regularly use special glazing oil to keep the rotor, basket and casing to prevent corrosion, and lubricate some parts, such as the axle and spindle of the basket, with lubricating oil. 3, a low speed centrifuge should use a separate outlet, to ensure a stable voltage; Voltage instability, such as that used by the user, must be connected to the power regulator, to avoid damage to the centrifuge; tabletop centrifuge should be placed firm, stable, horizontal On the countertop, leave some space around the chassis and keep it well ventilated. 4. After using the centrifuge, especially the frozen model, open the lid, clean the condensate and then dry it naturally, before and after the centrifugation, the rotor should be lowered or lifted gently vertically to avoid collisions with the shaft and turn the head same 5. Regularly use compressed air (vacuum) to remove dust from the heat sink on the back of the centrifuge body. Problems that should be paid attention to when operating Low-speed centrifuge: 1. use a separate low speed centrifuge socket, to ensure stable tension; voltage instability, such as a user, must be connected to the power supply, to avoid damage to the centrifuge; benchtop centrifuge to put strong, firm, the level around the table, leaving the enclosure Have a certain amount of space and keep it well ventilated. 2. a centrifuge after each use, in particular of frozen type, the lid should be opened, the condensed water was cleaned and then air; before and after centrifugation, it should be rotated down or upright gently raised and rotated around the same axis to avoid collisions. 3. Use a neutral detergent, such as soapy water, to clean dust from the centrifuge and residual samples, but toxic and radioactive substances should be specially treated. If it is found that the rotor is corroded and cracked, it should be replaced immediately. 4. turn the head, hanging basket, casing, etc., after use, should be dried and placed separately. 5. since glass tube breaks during centrifugation, in the case of the centrifuge chamber, the cleaned debris sleeve etc., will damage the centrifuge. In the upper part of the cavity can be coated petrolatum, put a few minutes of operation of the rotor, that is, the remains can be easily removed with Vaseline. 6. Use compressed air (vacuum) regularly to remove dust from the heat sink on the back of the centrifuge. 7. The centrifuge can be sterilized with the usual disinfectant. Content source: http://www.shlxy.com/html/8629571435.html




Send product request

To: Shanghai Lu Xiangyi centrifuge instrument Co., Ltd.
Your E-mail:
Message text:


Send to other suppliers

Other supplier products

Low-speed centrifuge
Low-speed centrifuge Low-speed centrifuge is a common model in the laboratory. The speed of the low speed centrifuge is lower than 10,000 rpm / min. The total volu...
High Speed Microcentrifuge
High Speed Microcentrifuge High Speed Microcentrifuge is especially suitable for micro-filtration at high speed. The general speed is 16000r/min, and the capacity is relative...
Cyto Centrifuge
Cyto Centrifuge Cyto Centrifuge and Cytology centrifuge widely used in immune hematology laboratories, for erythrocyte serological experiments, antigens, anti...
Cyto Centrifuge
Cyto Centrifuge Maintenance of Cyto Centrifuge 1. Before the centrifuge is operated, the power should be cut off and the centrifuge brake should be loosened ...
Large capacity centrifuge
Large capacity centrifuge large capacity centrifuge brushless inverter motor drive, microcomputer control, touch panel, programmable operation. With rotor identificatio...
All supplier products

Same products

LGJ-30S Top Press Type Experimental Freeze Dryer
LGJ-30S Top Press Type Experimental Freeze Dryer Seller: Beijing Songyuan Huaxing Technology Development Co., Ltd. LGJ-30S Top Press Type Experimental Freeze Dryer Technical parameters   freeze drying area:...
LGJ-30S Standard Type Experimental Freeze Dryer
LGJ-30S Standard Type Experimental Freeze Dryer Seller: Beijing Songyuan Huaxing Technology Development Co., Ltd. LGJ-30S Standard Type Experimental Freeze Dryer freeze area:0.43㎡   cold trap temp.:<-56℃ ...
LGJ-18S Multi Manifold Top Press Type Experimental Freeze Dryer
LGJ-18S Multi Manifold Top Press Type Experimental Freeze Dryer Seller: Beijing Songyuan Huaxing Technology Development Co., Ltd. LGJ-18S Multi Manifold Top Press Type Experimental Freeze Dryer Technical parameters   free...
LGJ-18S Multi Manifold Standard Type Experimental Freeze Dryer
LGJ-18S Multi Manifold Standard Type Experimental Freeze Dryer Seller: Beijing Songyuan Huaxing Technology Development Co., Ltd.  LGJ-18S Multi Manifold Standard Type Experimental Freeze Dryer Technical parameters:   freeze d...
LGJ-18S Top Press Type Experimental Freeze Dryer
LGJ-18S Top Press Type Experimental Freeze Dryer Seller: Beijing Songyuan Huaxing Technology Development Co., Ltd.  LGJ-18S Top Press Type Experimental Freeze Dryer Technical parameters:   freeze drying are...