KK03 Scratch tester
Product Introduction:
With the continuous expansion of the use of plastic molding products, from the point of view of the surface appearance of molded products (creativity)， improving scratch resistance (scratch characteristics) has become an important topic. And scratch resistance is also very important from the point of view that scars formed on the surface of the molded product may reduce the strength of the product. Scratch testing is performed by horizontal movement of the scratch needle against the pattern. Scratch characteristics were previously evaluated by a "constant vertical load test", but the American Society for Materials and Testing (ASTM) and the International Organization for Standardization (ISO) standardized the "vertical load test" (ASTM D7027-05/S019252)。
Scope of application:
The tester uses a steel needle to scratch films, plastics, automotive interior and exterior decorative materials, coating materials, etc., to evaluate the material's "scratch resistance" (scratch characteristics)。
Features of scratch tester:
1. Teaching function
Use this function to set the load zone with high precision before sampling.
2. Easy to operate with touch screen
All functions can be used and configured through the touch screen installed in front of the Settings.
3. the surface has a bump can also test scratches
The Yaru drive for vertical loads uses a county frame mechanism, so that even the surface with a concave and convex pattern can be tested without affecting the linear increase in load characteristics.
4. Memorizable test conditions
Storage capacity up to 20. capable of memorizing test conditions.
Technical parameters:
The KK-03 is fully compliant with I50 and ASTM international standards
Size :W545*D455*H680(mm)
Weight: About 150KG
Test mode: Load increase mode
Speed range :1——200 mm/sec
Load control range :0.1——5.00N
Horizontal (x) load test range :5N
Send product request
Other supplier products
 |
Diesel Water Ash Sulfur Mixing Tester | Meet the standard: ASTM D6304 ASTM D1744 ASTM D95 ASTM D482 ASTM D2622 ASTM D5453 ASTM D1266 Product Introduction: Analysis of water, ash, ... |
 |
Respirator Fit Tester | Hydrostatic Head Tester - Textile and Apparel - standard Applications: Overall Mask Leakage Test: Mask leakage is measured while the mask is ch... |
 |
Fabric Bursting Strength Tester | Standards: ASTM 3786-06、ISO 2758、ISO 13938-2、BS 3424 BS 3137、BS 4768、AS 2001.2.4、GB/T 7742 IWSTM 29、EDA NA 80.4-02、EDA NA 80.3-99、BS 2922 FZ/T 6... |
 |
Launder-Ometer Washing Fastness Tester | Testing Standards: ISO 105 C01 C02 C03 C04 C05 C06 C08 D01. BS 1006 C01 C02 C03 C04 C05. AATCC 28 61 86 132 151 190. NEXT TM2 3 5. M&S C4 C5 C... |
 |
KK01 Scratch tester | Product Introduction: With the continuous expansion of the use of plastic molding products, from the point of view of the surface appearance of mo... |
Same products
 |
Scott Flex Tester | Seller: Standard International Group (HK) Limited | Product Introduction: Scott kneading tester is suitable for back and forth kneading resistance o... |
 |
NEU nanofiber electrospinning device | Seller: Standard International Group (HK) Limited | Content The Nanofiber Electrospinning Unit uses electrospinning techniques to safely and easil... |
|
|
KK03 Scratch tester | Seller: Standard International Group (HK) Limited | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
 |
KK02 Scratch tester | Seller: Standard International Group (HK) Limited | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
|
|
KK01 Scratch tester | Seller: Standard International Group (HK) Limited | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
