Communication Equipment PCB

In order to shorten the signal transmission distance and reduce the signal transmission loss, the 5G communication board,Gradually move towards high-density wiring, fine wire spacing,The development of small aperture, thin profile and high reliability.

Process Difficulty Of High Frequency And High Speed PCB Board

Alignment Accuracy

Accuracy is tightened, and tolerance convergence between layers is required. The board size becomes more demanding for this convergence requirement

Size Gets Bigger

Machinability deteriorates, maneuverability deteriorates, and blind holes need to be buried 1. Cost increase 2. Difficulty in alignment accuracy

Impedance Accuracy

The etching challenge is great:

STUB (Impedance Is Not Continuous)

STUB is tightened, board thickness fluctuation is extremely challenging, and back drilling technology is required

Increased Signal Loss Demand

It is a big challenge for all copper clad laminates; the tolerance requirements for PCB thickness are high, including length, width, thickness, perpendicularity, bow and twist, etc.

The Number Of Layers Becomes Higher

Features such as denser lines and vias, larger cell size, thinner dielectric layer, etc., more stringent requirements for inner layer space, interlayer alignment, impedance control, and reliability

Accumulated Experience In Manufacturing Communication Board Of Huihe Circuits

High Density Requirements:

The influence of crosstalk (noise) will decrease as the line width/spacing (L/S) shrinks.

Strict Impedance Requirements:

Characteristic impedance matching is the most basic requirement for high-frequency microwave boards. The greater the impedance, the greater the ability to prevent the signal from penetrating the dielectric layer, the faster the signal transmission and the smaller the loss.

Transmission Line Production Accuracy Is High:

The transmission of high-frequency signals has strict requirements on the characteristic impedance of the printed wire, that is, the production accuracy of the transmission line is generally ±lmil, and the edges of the transmission line must be very neat, and no burrs, gaps, or repairs are allowed. line.

Mechanical Processing Requirements:

First, the high-frequency microwave board material is very different from the epoxy glass cloth material of the printed board in terms of machining; secondly, the processing accuracy of the high-frequency microwave board is higher than that of the printed board. Many, the general shape tolerance is ±0.1mm (in the case of high accuracy, the shape tolerance is ±0.05mm).

Mixed Pressure:

The mixed use of high-frequency substrates (PTFE-based) and high-speed substrates (PPE-based) makes the high-frequency and high-speed circuit board not only have a large conduction area, but also have a stable dielectric constant, high dielectric shielding requirements, and high temperature resistance. At the same time, it should be solved that the differences in the bonding force and thermal expansion coefficient between the two different plates lead to the undesirable phenomenon of delamination and mixed pressure warping during the processing.

The Coating Uniformity Requirements Are High:

The characteristic impedance of the high-frequency microwave board transmission line directly affects the transmission quality of the microwave signal. The characteristic impedance has a certain relationship with the thickness of the copper foil. Especially for microwave plates with hole metallization, the plating thickness not only affects the total copper foil thickness, but also affects the accuracy of the wire after etching, so the size and uniformity of the plating thickness Need to be strictly controlled.

Laser Micro-Via Processing:

The important feature of high-density boards for communication is the micro-via with blind/buried via structure (aperture ≤0.15mm). The formation of tiny vias is currently mainly laser processing. The ratio of the diameter of the via hole to the diameter of the land may vary from supplier to supplier. The ratio of the diameter of the via hole to the connecting plate is related to the accuracy of drilling positioning. The more stacks, the greater the deviation may be. At present, the target positioning is tracked layer by layer. For high-density wiring, there have been vias without land.

Surface Treatment Is More Complicated:

As the frequency increases, the choice of surface treatment becomes more and more important; a thin coating with good electrical conductivity has the least impact on the signal. The “roughness” of the wire must match the transmission thickness that the transmission signal can accept, otherwise it is easy to produce serious signal “standing waves” and “reflections”. The molecular inertness of special substrates such as PTFE makes it difficult to combine with copper foil. Special surface treatment is required to increase the surface roughness or add a layer of adhesive film between the copper foil and PTFE to improve the bonding force.

Huihe Circuits is a professional printed circuit board maker, we provide communication pcb, pcb audio, audio circuit boardand etc. Want to know more? Please contact us.

Other supplier products

	10 Layer ENIG Blind Vias PCB	Number of layers: 10 Surface finish: ENIG Base material: FR4 W/S: 4/4mil Thickness: 1.6mm Special process: Blind Vias Advantages Of 10 Laye...
	Communication Equipment PCB	In order to shorten the signal transmission distance and reduce the signal transmission loss, the 5G communication board,Gradually move towards hig...
	6 Layer HASL Blind Buried Via PCB	Number of layers: 6 Surface finish: HASL Base material: FR4 Outer Layer W/S: 9/4mil Inner layer W/S: 11/7mil Thickness:1.6mm Special process:...
	PCB Application	PCB Application As a leading PCB supplierin Chinaprinted circuit board industry , HUIHE Circuits PCB board application including communications,...
	2 Layer OSP Impedance Control Half Hole PCB	Number of layers: 2 Surface finish: OSP Base material: FR4 Outer Layer W/S: 6/4mil Thickness: 1.0mm Special process: impedance control+half ho...

供应产品

Same products

	DM-16BF DM-18BF New cover Electric Sprayer	卖方: Zhejiang Huaqi Information Technology Co., LTD	The Electric Knapsack Sprayer is a game-changer in the field of agricultural pest control. Engine...
	Simple Round Breeding Cage	卖方: Zhejiang Huaqi Information Technology Co., LTD	The Simple Round Breeding Cage features a durable and lightweight construction, making it suitabl...
	叙利亚-细胞储存液氮容器-液氮液位报警器	卖方: 河南天之道生物科技有限公司	精准的实验条件与安全的样本存储是科研工作顺利开展的关键要素。其中，细胞储存液氮罐作为实验室不可缺少的一种设备，在样本保存方面发挥着重要的作用。 实验室用的细胞储存液氮罐，航空铝制造，重量轻、占用...
	意大利-液氮细胞储存罐-液氮罐液位报警器	卖方: 河南天驰仪器设备有限公司	精准的实验条件与安全的样本存储是科研工作顺利开展的关键要素。其中，细胞储存液氮罐作为实验室不可缺少的一种设备，在样本保存方面发挥着重要的作用。 实验室用的细胞储存液氮罐，航空铝制造，重量轻、占用...
	埃及-细胞储存液氮罐-液氮液位监测仪	卖方: Henan Tianzhidao Biological Technology Co., Ltd.	精准的实验条件与安全的样本存储是科研工作顺利开展的关键要素。其中，细胞储存液氮罐作为实验室不可缺少的一种设备，在样本保存方面发挥着重要的作用。 实验室用的细胞储存液氮罐，航空铝制造，重量轻、占用...