Swing Check Valve

What is a Swing Check Valve?

A Swing Check Valve is desinged to prevent the medium in the pipeline from flowing back. As pressure reaches zero, the valve shuts fully to prevent backflow.

Swing check valves belong to the group of automatic valves, which are used mostly in pipelines where the medium flows in one direction and allow only the medium to flow in one direction to avoid accidents. The pressure drops and turbulence in these types of valves are very low. This type of valve should generally be installed horizontally in the pipeline, but it can also be installed vertically by keeping in mind that the disc cannot reach the stalling position where the disc stuck in an open position.

How does a Swing Check Valve work?

One end of a disc-shaped disc is made into a “wing-type” structure, which is free to move by hanging on a body, etc., and has a structure in which pressure loss is small and fluid flows easily. It can be used not only for horizontal piping, but also for vertical piping (flowing from bottom to top).

Swing Type Check Valve for Sale

Stainless Steel Swing Check Valve

Stainless Steel Swing Check Valve ZECO is professionalswing check valve manufacturer, stainless steel materials can be selected ASTM A351 CF8, ASTM A351 CF8M, ASTM A351 CF3, ASTM A351 CF3M, UNS S32205.

High Temperature Check Valve

High Temperature Check Valve The seat of ZECO high-temperature check valve is designed renewable. When the seat needs to be replaced over time, do not remove the entire valve, just remove the bonnet and replace the seat.

Applications of Swing Check Valve

Power plants. A variant of the standard swing check valve, silent check valves — also called spring check valves — use a spring to help the valve close with more control. Silent check valves see frequent use in fluid control applications in the power generation sector, such as cooling towers. Of note, it also takes more pressure to open the valve against the spring, so spring check valves are best suited to high-pressure applications.

Natural gas transmission. Swing check valves help prevent the improper flow of gas that could result in dangerous leaks or fires. These valves see broad usage in gas pipelines, commercial and residential gas meters, gas compressors, and more.

Oil and gas refineries. Refineries often use specially designed non-slam check valves to mitigate water hammer — the pressure wave created in the system by a slamming valve.

Horizontal water lines. Swing check valves are ideal for high-volume, consistent-pressure fluid situations. They’re the most common valve used in wastewater treatment and water pumping.

Custom solutions. Each system is different, and sometimes specific applications require a unique modification or entirely original design to solve a challenging flow issue. It may be as simple as changing the angle of the valve or decreasing the disc’s weight, but your valve manufacturer can help you determine if a customized solution is right for you.

Installation of Swing Check Valve

Inspection

Threads of mating pipe must be clean and machined to appropriate ANSI/ASME specifications. Ends of mating copper tubing or pipe must be square and free of burrs. Use emery cloth to clean and remove grease and/or oxidation before soldering. Inspect sealing surfaces of valve for cleanliness prior to installing.

Mounting

Swing check valves can be mounted in either vertical or horizontal position with upward flow or in any intermediate position. Flow must be by direction of arrow in body. It is not recommended that swing check valve be mounted in close proximity to reciprocating pumps or compressors due constant pressure fluctuations which shortens the life of the valve.

NPT connection

It is recommended that the valve is mounted in the closed position. Gently thread valve to mating pipe by hand until resistance is felt. Using a wrench tighten the valve using the hex flats at the joint being tightened. Do not tighten through the valve body using hex flats on opposite end of joint being tightened.

Solder connection

It is recommended that the valve be in the open position. Care must be taken to apply the proper amount of solder so that it does not flow into valve seat area. During soldering, the mid-portion of the valve body should not exceed 300°F. This can be monitored using an infra-red temperature sensor. Depending on the fuel selected and the orientation of the installation it may be necessary to wrap the valve body with wet rags or employ other heat absorbing techniques. The flame must be directed away from the valve body, concentrated on the solder cup. The cup should be heated evenly. Once one of the joints is complete, the valve should be allowed to cool until “cool to the touch” before beginning the second joint.

As one of international valve suppliers, we can offer types of related products for sale, if you have needs, please contact us.

As an industrial valve manufacturer, ZECO always adheres to exceeding customer expectations, to provide customers with more value-added services and products as the ultimate goal.

Other supplier products

	Stainless Steel Globe Valve	Description of Stainless Steel Globe Valve: The principle of ZECO stainless steel globe valve is that through the drive mechanism to make stem and ...
	56 Inch Ball Valve	Description of 56 Inch Ball Valve: The largest size ball valve produced by ZECO is 56 inch, and it has its own mold, which can catch up with users'...
	Resilient Gate Valve for Underground	Basic informationThis underground gate valveis used as a two-way closed circuit device.Features1. No need for sluice Wells, which reduces the amoun...
	Cryogenic Gate Valve	Categories: Gate Valve, Gate Valve By Material Tag: OS&Y Valve Description Cryogenic gate valves are adapted to special conditions of serv...
	3 Inch Butterfly Valve	Description of 3 Inch flanged Butterfly Valve: ZECO 3 butterfly valveis a small diameter butterfly valve, usually manually operated, and the connec...

供应产品

Same products

	Fischer Tropsch wax used for the processing of leather care products	卖方: Syntop chemical Co.,Ltd.	Fischer Tropsch wax plays a significant role in the formulation of leather care products, primari...
	Alloy Steel Precision Cast Construction Machinery Parts	卖方: NingBo YinZhou ChengEn Machinery CO.,Ltd.	Application ScenariosEarthmoving Machinery: Bucket teeth, boom connectors Mining Equipment: Crus...
	Fischer Tropsch Wax with high melting point for adhesive	卖方: Syntop chemical Co.,Ltd.	Fischer Tropsch wax is an ideal additive in adhesive processing, particularly in the field of EVA...
	iFixes iT23 液晶屏开启器	卖方: 深圳市维客修科技有限公司	iT23液晶屏开启器，安全便捷地修复iPhone X-17系列手机及平板屏幕电脑。
	High medium low melting point Fischer Tropsch wax for candle	卖方: Syntop chemical Co.,Ltd.	Main Applications of Fischer-Tropsch Wax in Candle Manufacturing ‌Enhancing Gloss and Aesth...