CA Series-330CA30 PEEK Carbon Fiber Reinforcement
CA Series-330CA30 peek fccarbon fiber reinforcement is suitable for the production of bushing seals and other products, can be faster from the bearing surface heat dissipation, at the same time has a high thermal deformation temperature (336 ° C) , also can maintain strength at high temperature, to a certain extent, can replace metal materials.
Specification of CA Series-330CA30 PEEK Carbon Fiber Reinforcement
Material Properties |
Test Method |
Conditions |
Units |
770G |
Mechanical Data |
||||
Tensile Strength |
ISO 527 |
B reak,23℃ |
MPa |
- |
Y ield,23℃ |
MPa |
100 |
||
Tensile Elogation |
ISO 527 |
Break,23℃ |
% |
45 |
Flexural Strength |
ISO 178 |
Break,23℃ |
MPa |
- |
Y ield,23℃ |
MPa |
165 |
||
Fleoural Modulus |
ISO 178 |
23℃ |
Gpa |
|
Compressive Strength |
ISO 604 |
23℃ |
MPa |
125 |
Charpy Impact Strength |
ISO 179/leA |
Notched |
kJm-2 |
7 |
ISO 179/IU |
Unnotched |
kJm-2 |
- |
|
Izod Impact Strength |
ISO 180/A |
Notched |
kJm-2 |
|
ISO 180/U |
Unnotched |
kJm-2 |
- |
|
Mould Shrinkage |
ISO 294-4 |
Along flow |
% |
1 |
Across flow |
% |
|||
Thermal Data |
||||
Melting Point |
ISO 11357 |
℃ |
343 |
|
Glass Tansition (Tg) |
ISO 11357 |
Onset |
℃ |
143 |
Special Heat Capacity |
DSC |
23℃ |
kj kg-1℃-1 |
|
Coefficient of Thermal Expansion |
ISO 11359 |
Along flow below Tg |
ppm K-1 |
45 |
Along flow above Tg |
ppm K-1 |
120 |
||
Heat Deflecion Temperature |
ISO 75A-f |
℃ |
152 |
|
Thermal Conductivity |
ASTM C177 |
23℃ |
W m-1K-1 |
|
Flow |
||||
MeltIndex |
ISO 1133 |
380℃,5kg |
g10min-1 |
10 |
Miscellaneous |
||||
Density |
ISO 1186 |
Crystalline |
gcm-3 |
|
Amorphous |
gcm-3 |
|||
Shore D Hardness |
ISO 868 |
23℃ |
85 |
|
Water Absorption(3.2mm thick Tensile Bar) |
ISO 62-1 |
24h,23℃ |
% |
|
by immersion |
Equilib riu m,23℃ |
% |
||
Electrical Data |
||||
Dielectric Strength |
IEC 60243-1 |
2mm |
kV mm-1 |
23 |
Comparative Tracking Index |
IEC 60112 |
V |
150 |
|
Dielectric Constant |
IEC 60250 |
23℃,1kHz |
||
23℃,50kHz |
3 |
|||
Loss Tangent |
IEC 60250 |
23℃,1MHz |
||
Volume Resistivity |
IEC 60093 |
23℃,1V |
Ω cm |
10 16 |
275℃ |
Ω cm |
10 9 |
As one of peek suppliers, we can offer kinds of peek plastic materialfor sale, anything you need, please contact us.
在线联系供应商
Other supplier products
PEEK Seal Material in Mechanical | PEEK Seal Materialin Mechanical PEEK is a kind of mateiral with both rigidity and toughness, excellent mechanical properties, wear resistance, s... | |
PEEK in Wires & Cables | peek wire insulation PEEK in Wires & Cables PEEK has outstanding heat aging properties, good flame retardancy, self-extinguishing, hydr... | |
CA Series-770CA30 PEEK Carbon Fiber Reinforcement | CA Series-770CA30carbon filled peekreinforcement is widely used in automobile and aviation fields. It is widely used in automobile fuel pump and ge... | |
Grade PF PEEK Pure Resin Fine Powder | The material is obtained by grinding the coarse powder (D50 is 13 micron ~ 75 microns). It can be used as moulding material, spraying material and ... | |
Grade PF PEEK Pure Resin Fine Powder | The material is obtained by grinding the coarse powder (D50 is 13 micron ~ 75 microns) . It can be used as moulding material, spraying material and... |
Same products
ETH Ethereum Jasminer X4 BRICK ASIC Miner | 卖方: Shenzhen Dovina Electronic Co.,Ltd | Jasminer X4 Brick Review Jasminer x4 brick for salefrom Jasminer mining EtHash algorithm with a ... | |
ETH Ethereum Jasminer X4-1U ASIC Miner | 卖方: Shenzhen Dovina Electronic Co.,Ltd | TheJasminerx4-u1 miner has a different look than the X4 mining unit. So you get a miner with a sl... | |
ETH Ethereum Jasminer X16 ASIC Miner | 卖方: Shenzhen Dovina Electronic Co.,Ltd | Model X16Qfrom Jasminer mining EtHash algorithm with a maximum hashrate of 1.845Gh/s for a power ... | |
ETH Ethereum iPollo V1 Mini SE Plus ASIC Miner | 卖方: Shenzhen Dovina Electronic Co.,Ltd | Model V1 Mini SE Plusfrom iPollo mining EtHash algorithm with a maximum hashrate of 400Mh/s for a... | |
ETH Ethereum iPollo V1 Mini SE ASIC Miner | 卖方: Shenzhen Dovina Electronic Co.,Ltd | Model V1 Mini SEfrom iPollo mining EtHash algorithm with a maximum hashrate of 200Mh/s for a powe... |