oxygen generator
Working principleVacuum pressure swing adsorption air separation oxygen adsorption process of vacuum desorption is a super-atmospheric pressure, the oxygen molecular sieve to select the nitrogen adsorption in the air under pressure, but is not the adsorption of oxygen enriched product gas at the top of the adsorption tower output at the same time, another adsorption tower vacuum regeneration. When the adsorption tower in the adsorption state of near saturation prior to the tower automatic decompression desorption regeneration and other renewable adsorption tower pressurized adsorption system to take oxygen. This cycle, the two adsorption towers alternately repeated oxygen production and regeneration to achieve continuous preparation of oxygen.
Oxygen and nitrogen close to the boiling point, both difficult to isolate, in the gas phase with enrichment. The vacuum pressure swing adsorption oxygen generator usually only a purity of 90 to 95% oxygen (oxygen limit of 95.6% purity, the rest is argon), also known as oxygen-rich. Compared with the cryogenic air separation unit, which can be produced from the purity more than 99.5 percent oxygen.Technical FeaturesOxygen scale of 10000m3 / h below the oxygen, lower power consumption, smaller investment;
Civil small amount of the installation cycle is shorter than the cryogenic air separation unit;
Device operation and low maintenance costs;
Devices run high degree of automation, open parking is convenient, less operating personnel;
Device operation stability, safe;
Simple operation, the main components are the selection of internationally renowned manufacturers;
The use of imported oxygen zeolite, superior performance, long life;
Technical indicatorsOxygen production: 100 ~ 10000Nm3 / h
Oxygen purity: ≥ 90 to 95% (according to user requirements to be adjusted within the range of 30 to 95 percent)
Oxygen pressure: ≤ 20KPa (supercharged)
Other supplier products
|
|
oxygen generator |
Oxygen plant
Main technique target of Oxygen plant
Products Capacity （m³/hr） Purity（%） Pressure（Mpa）
Oxygen 50-2000 99.6-99.8 0.25-22
L... |
|
|
oxygen generator |
Main technique target of Nitrogen Plant
Products Capacity （m³/hr） Purity（%） Pressure（Mpa）
Oxygen
Liquid Oxygen
Nitrogen 50... |
|
|
oxygen generator |
The role of catalyst, the reaction of low purity nitrogen, oxygen system by adding hydrogen to generate water to remove residual oxygen after furth... |
|
|
oxygen generator |
Main technique target of Nitrogen Plant
Products Capacity （m³/hr） Purity（%） Pressure（Mpa）
Oxygen
Liquid Oxygen
Nitrogen 50... |
|
|
oxygen generator |
Oxygen plant
Main technique target of Oxygen plant
Products Capacity （m³/hr） Purity（%） Pressure（Mpa）
Oxygen 50-2000 99.6-99.8 0... |
供应产品
Same products
|
|
尖心轨降低值测量尺 |
卖方: 842518 |
辙叉垂直磨耗测量尺用于测量辙叉心轨与翼轨磨损段任意部位的垂直磨耗值及心轨相对于翼轨的缩减值，具有测量精度高、现场工人容易掌握、可靠性高、体积小、重量轻等显著优点。 |
|
|
便携式激光弦线 |
卖方: 842518 |
激光准直仪用于测量轨道水平和线路，以辅助轨道测量和人工捣固作业。它可以测量水平和垂直。它主要由激光发射装置、靶标定位装置和移动定位靶标装置组成。 |
|
|
轨底坡测量装置 |
卖方: 842518 |
Основная часть катания колеса имеет наклон внутрь 1:40. Для того чтобы верхняя часть рельсового п... |
|
|
NGM-6.3II型内燃钢轨打磨机 |
卖方: 842518 |
该机主要用于铁路钢轨维护施工中的焊缝恢复打磨、压延毛刺、轨面修复、波形磨损等。该机不仅仿形精度、打磨效率等技术性能有较大提高，而且由于数控进给单元的开发应用，实现了砂轮进给的智能控制，大大简化了... |
|
|
NCM-5.1型内燃道岔打磨机 |
卖方: 842518 |
NCM-5.1道岔打磨机是专门针对道岔、交叉口及轨头两侧的打磨作业而设计的。该机打磨装置可从垂直方向向左右倾斜30°，并可沿纵横方向调整打磨轮的位置，使该机打磨装置在钢轨间狭小空间内也能... |
