Explosion Proof Products for Class I Division 2
What is A Class 1 Div 2 Area?
Class 1 Div 2 Definition
In Simple Word
Class 1 Div 2 location, C1D2 for short, Class 1 Division 2 for full name, means ignitable concentrations of hazards, such as flammable vapors and gases, exists under abnormal operation conditions.
In Quantitative Measurement
Class 1 DIV2 light switchlocation means ignitable concentrations of hazards, such as flammable vapors and gases, present from 1 hour to 10 hours every year.
Class 1 Division 2 Electrical Requirements
In Accordance with NEC Article 500
A Class 1, Division 2 location is a location:
In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or
In which ignitible concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation and which might become hazardous through failure or abnormal operation of the ventilating equipment, or
That is adjacent to a Class 1, Division 1 location, and to which ignitible concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors above their flash points might occasionally be communicated unless such communication is prevented by adequate positive-pressure ventilation from a source of clean air and effective safeguards against ventilation failure are provided.
Explosion Proof High Bay Lighting
Explosion Proof Led High Bay Lights Class 1 Div 1 Zone 1 SHB Series
Class I Division 1
Zone 1&2, Zone 21&22
LED 30-240W
Type 4X, IP66
Explosion Proof Led High Bay Lights Class 1 Div 1 Zone 1 SO-I Series
Class I Division 1
Zone 1&2, Zone 21&22
LED 30-150W
Type 4X, IP66
Explosion Proof Led High Bay Lights Class 1 Div 2 Zone 2 SHB-II Series
Class 1 DIV2 Fluorescent Lighting
Zone 2, Zone 21&22
LED 30-300W
Type 4X, IP66
Explosion Proof Led High Bay Lights Class 1 Div 2 Zone 2 SVM Series
Class I Division 2
Zone 2, Zone 21&22
LED 30-300W
Type 4X, IP66
Explosion Proof Flood Light
Explosion Proof Led Flood Light Class 1 Div 1 Zone 1 SHF-I Series
Class I Division 1
Zone 1&2, Zone 21&22
Type 4X, IP66
Explosion Proof Led Flood Light Class 1 Div 1 Zone 1 SHF-IA Series
Class I Division 1
Zone 1&2, Zone 21&22
LED 20-200W
Type 4X, IP66
Explosion Proof Led Flood Light Class 1 Div 2 Zone 2 SHF-IIA Series
Class I Division 2
Zone 2, Zone 21&22
LED 20-400W
Type 4X, IP66
Explosion Proof Led Street Light Class 1 Div 1 Zone 1 SSL Series
Class I Division 1
Zone 1&2, Zone 21&22
LED 80-300W
Type 4X, IP66
Explosion Proof Led Gas Station Canopy Lights Class 1 Div 2 Zone 2 SCP Series
Class I Division 2
Zone 2, Zone 21&22
LED 40-150W
Type 4X, IP66
Explosion Proof Fluorescent Lighting
Explosion Proof Led Linear Fluorescent Lights Class 1 Div 1 Zone 1 SLL-I Series
Class I Division 1
Zone 1&2, Zone 21&22
LED 20-120W
Type 4X, IP66
Explosion Proof Led Linear Fluorescent Lights Class 1 Div 2 Zone 2 SLL-II Series
Class I Division 2
Zone 2, Zone 21&22
LED 20-80W
Type 4X, IP66
Explosion Proof Led Linear Fluorescent Lights Class 1 Div 2 Zone 2 SLe Series
Class I Division 2
Zone 1&2, Zone 21&22
LED 9-80W
Type 4X, IP66
Explosion Proof Emergency Lighting
Explosion Proof Led Emergency Bug-eye Lights SEG Series
Class I Division 1
Zone 1&2, Zone 21&22
LED 2x5W
Type 4X, IP66
Explosion Proof Led Emergency Exit Sign Lights SES Series
Class I Division 1
Zone 1&2, Zone 21&22
LED 5W
Type 4X, IP66
Explosion Proof Alarm Lights SAV Series
Class I Division 1
Zone 1&2, Zone 21&22
LED 5W
Type 4X, IP66
Explosion Proof Flashlight
Explosion Proof Led Class 1 Div 1 Flashlight SPL-A Series
Class I Division 1
Zone 1&2, Zone 21&22
LED 2x5W
Type 4X, IP67
Explosion Proof Led Class 1 Div 1 Torch Lights SPL-B Series
Class I Division 1
Zone 1&2, Zone 21&22
LED 5W
Type 4X, IP65
Explosion Proof Led Division 2 Flashlight SPL-C Series
Class I Division 1
Zone 1&2, Zone 21&22
LED 5W
Type 4X, IP68
Explosion Proof Led Flashlight Portable Search Lights SPL-D Series
Class I Division 1
Zone 1&2, Zone 21&22
LED 2x5W
Type 4X, IP65
Explosion Proof Led Flashlight Portable Work Lights SPL-E Series
Class I Division 1
Zone 1&2, Zone 21&22
LED 5W
Type 4X, IP65
Explosion Proof Led Flashlight Portable Headlamp SPL-F Series
Class I Division 1
Zone 1&2, Zone 21&22
LED 5W
Type 4X, IP67
Explosion Proof Led Flashlight Portable Headlamp SPL-F Series
FAQ for Class 1 Div 2
Q
Does Class 1 Div 2 require explosion proof?
A
Yes, Class 1 Div 2 require explosion proof. According to Class 1 Div 2 requirements, considering the existing frequency of ignitable gas of Class 1 Div 2 is not higher than Class 1 Div 1, led lighting should at least be constructed properly as “explosion proof” to limit the energy or isolate the ignition sources physically to prevent future explosion from happening, let alone the spreading of explosion.
Q
What is a Class 1 Division 2 hazardous area? What is a C1D2 room?
A
Class 1 Division 2 hazardous area produce flammable vapors or gases which are further divided into Class 1 Division 2 Groups A-D. Hazardous material come out in abnormal conditions, such as system or container failures, leaks or ruptures and do not expected to always exist, only under unusual conditions. C1D2 room should install electrical device abide by electrical rating class 1 division 2.
FAQ for Explosion Proof Lighting Class 1 Div 2
FAQ for Explosion Proof High Bay Lighting Class 1 Div 2
Q
Is NEMA 4X good for Class 1 Div 2?
A
Yes, when you intend to use electrical enclosure or panel in hazardous location, it is crucial to keep any combustible substances such as gases, vapors from entering into the confined housing and influencing the working of the electrical components inside. NEMA 4 and NEMA 4X protection rating lay the rational foundation for anti-explosion performance of nema 4x class 1 division 2 explosion proof enclosure.
Q
What is a Class 1 Div 2 enclosure?
A
Class 1 Division 2 Enclosure is used in facilities that flammable gases, vapors, and liquid materials are unlikely to present. Different from Class 1 Div 1 enclosure, Class 1 Div 2 enclosure should be factory sealed with at least Nema 4X rated standard as “nema explosion proof”, housed by glass reinforced plastic, stainless steel or aluminum alloy material control the potential to bring about ignition source via restrain high heat, temperature of electrical parts.
Q
Does Class 1 Div 2 require seal offs?
A
Yes, no matter what kind of outlets from such as conduit system, cables, cable entries of light fixtures, boxes, receptacles, switches, when the environment meet the electrical rating class 1 division 2 or flammable gas or vapors spread through any space or gaps within the whole system, sealing off for any bonding surface is essential to reduce the risk for concentration of hazards subject to class 1 div 2 seal off requirement.
If you want to know more different kinds of explosion proof led light fixtures, please visit our website.
在线联系供应商
Other supplier products
Industrial Lighting from SUREALL | Industrial led lighting china, also called industrial light fixture, industrial light fixtures, led lighting, led lights, waterproof led lights, le... | |
200w Led Street Lighting | Products Show for 200w Led Street Lighting Led street light 200 wattonly include 200w explosion proof street light, 200w flame proof street light,... | |
Explosion Proof Receptacle Explosion Proof Socket and Plug SSP-P Series | Flame Proof SocketExplosion Proof Switches And Atex SocketsFlame Proof Socket Explosion Proof Receptacle Explosion Proof Socket and Plug SSP-P S... | |
Explosion Proof Alarm Lights SAV Series Advantages | Class I, Division 1, Groups C, D Ex tD A21 IP66 T80°C Db IP66 Class I, Division 2, Groups A, B, C, D Zone 1, Zone 2 Class II, Division 1, G... | |
Explosion Proof Fluorescent Lighting | Products Show for Explosion Proof Fluorescent Lighting T8, led tube light fittings to be used as fluorescent light, linear high bay light, led... |
Same products
T11A LED Road Lighting | 卖方: Hangzhou Hpwinner Opto Corporation | T11A LED Road Lighting The wattage range of T11ALED road lighting 40W -420W T11A street light... | |
Side-entry & Post-top LED Roadway Light | 卖方: Hangzhou Hpwinner Opto Corporation | Side-entry & Post-top LED Roadway Light HPWINNER side-entry & post-top LED roadway light... | |
Side-entry LED Road Light | 卖方: Hangzhou Hpwinner Opto Corporation | Side-entry LED Road Light HPWINNER side-entry LED road Lights are designed for the poles with ar... | |
M6A-VC LED Module | 卖方: Hangzhou Hpwinner Opto Corporation | M6A-VC LED Module The wattage range of M6A-XC IP68 LEDMini Module20W/25W/30W As one of the el... | |
LED Grow Light | 卖方: XIAMEN TOPSTAR LIGHTING CO.,LTD | Since LED lights appeared on the marketing, LED grow lightsare becoming popular day by day. As a ... |