GIRDER CARRIER

Girder Carriercarrying capacities of 120T, 160T, 180T, 220T, 250T, and 300T that can be used directly to feed girder to bridge launcher and coordinate cross hole of bridge crane, featuring self-propelled, concrete girder without limitation of length, user- friendly operation, and maintenance, lower cost of transportation and good stability. Girder prefabrication field and bridging construction site with a weakness of long-distance and complex traffic, as well as the construction site where is not suitable for the track- laying or is in high cost of track- laying, etc. are also applicable. Girder Carrier takes place of traditional equipment. Many impressive performances have been achieved in girder transportation with an active presentation recently. Girder carrier comes from engineering, and will also apply to engineering practice, enabling bridge engineer well- content.

HOW DOES GIRDER CARRIER WORK

Check Before Vehicle Moving

All working points of engine oil level, hydraulic oil, fuel oil, cooling water, brake device, stored battery, transmission mechanism, starting device, lubricating condition of each joint, and tire pressure of all working points must be checked.

Diesel engine part please see use and maintenance manual instruction.

When starting up, place the gear lever in the neutral position, strain the manual valve, and then switch on with the use of a key (turn the key clockwise to ACC gear).

Ride the clutch pedal to continue to start the engine by turning the key. Once the engine is started up, loosen the key immediately. Each starting time should be no more than 15 seconds, so order to protect the starter and stored battery. After starting failure of each time, try again after 60 seconds. If three starting fail, it shall find out the causes. It can only start the engine after troubleshooting. Evenly loosen the clutch pedal, after the stable running of the engine.

After starting, pay attention to check the oil pressure. When a diesel engine runs at an idle speed, engine oil pressure should be no less than 0.1Mpa (1 kgcm2). Check the oil surface of the oil pan for a new-assembly diesel engine after starting 5 minutes. Add the engine oil in-between upper and down marks of the oil scale, when necessary.

Girder trailer shall check immediately whether cooling water enters into the water jacket of the diesel engine 5 minutes after starting of diesel engine.

When starting, do not ride the accelerator fiercely, in case of the sudden rise of engine oil pressure. Feeding-up engine oil can't reach friction surfaces of various parts, leading to quick wear of the parts.

Warnings For Use In Winter

Use in winter must be injected F35 anti-freezing solution. The radiator curtain must be put down before the engine starts.

When starting the engine, firstly press preheats button, and then start the engine with the key.

When starting the engine in winter air temperature below -35 ℃, if the warm machine with hot water is used, the water temperature should not be too high, avoiding cracking of the cylinder.

Correctly choose engine oil according to the environmental temperature; When the temperature is lower than 0 ℃, use winter engine oil (see the engine fuel part).

Vehicle Starting

Confirm the manual valve in the terminating braking state. After the engine starts, it shall run at a low speed for a few minutes. The vehicle can start moving when the water temperature reaches 50 ℃. Don't run at an idle speed for a long time.

Work divisions for personnel of the main vehicle and the front vehicle should be defined clearly with united command.

Starting can only be conducted after completion of all preparations and confirmation meeting requirements.

When starting, break (breaking device) releases. Start from gear 1, which has similar starting method with a car.

Vehicle Moving

The vehicle can only start moving under the situations of the normal running of the engine, normal functions of all instruments, indicator lights, and alarm lights.

A manual valve should be placed on the break-releasing position when starting.

During vehicle running, pay attention to keeping the engine coolant temperature between 75 and 95 ℃.

Pay attention to observing oil pressure that should be not less than 170 kPa when running at a low speed; not less than 441 kPa at a high speed. Otherwise, it shall stop the vehicle for inspection in case of component burnout.

During vehicle running, if a certain part fails, for example, air storage tank pressure is decreased, the warning light will be on. At the moment, the vehicle should stop and strain the manual valve. Running can start after troubleshooting and light off.

In the general situation, try to not start in a hurry, accelerate suddenly and have an emergency braking.

When gear shifting, the girder carrier shall have an even-strength and engage the gear to the bottom. If it's difficult to shift gear, then it shall adjust the variable-speed control mechanism.

During vehicle running, don't put your foot on the clutch pedal all the time. The foot shall leave the pedal after gear shifting.

Don't shift the gear without riding on the clutch.

Reverse gear can only be engaged after the vehicle is parked completely.

When the engine running, it shall listen often to check whether it's abnormal noise. The problem detected should be solved immediately before the vehicle runs.

Proper Use of the Clutch

The clutch is only used for change speed gear shifting or controlling the clutch working in half on-off state in a flat road in a short time in order to lower the speed. When loading vehicle climbs or descends the slope, the clutch and empty load are prohibited to use.

Vehicle Stop

Lower speed, vehicle stops after running at an idle speed. After that, take out the switch key. Gear position must be in a position with gear and hand brake in the braking position after vehicle stop. Use triangle wood to stuff the front and rear tires up.

Braking Method

During vehicle running, if failure indicator of braking system flashes or air pressure is not enough, it shall stop the vehicle for inspection.

Check whether there is leak in all pipelines and connectors, and whether the air pump is working .

Unless in emergency, use of emergency brake should be avoided.

☆ Emergency brake can make tires lock up, leading to vehicle slip.

☆ When the transporting girder vehicle descends the slope or runs on the dirt, snow, freezing road or other good roads, full attentions should be paid.

☆ Emergency braking operation will cause early wear of the tire and lead to other bad effects on other devices on the vehicle.

☆ Emergency braking will exert a great impact on concrete girder, which may cause injury and other accidents.

It's not allowed to ride on the braking pedal continuously, otherwise the braking pressure will be reduced, causing a bad effect on braking.

It's not allowed to have an excessive use of service brake, or brake will be overheated, significantly reducing the braking effect.

Driving on the Slope

When descending the slope, the engine should be used for dragging, and also shift control level should be placed on gear 1 position.

* When the dragging force is insufficient, braking can be achieved with feet.

* In order to reduce wear and heating phenomenon during braking, it shall firstly lower vehicle speed and engage in gear 1 in advance before descending down the slope.

* It shall engage in gear 1 in advance before climbing the slope.

When descending the slope, it is forbidden to stall the engine.

When the transporting girder vehicle climbs or descends the slope with girders loaded, it is strictly prohibited to use the clutch and empty space as well as gear shifting. It's better not to stop.

Others

The starting and running of diesel engine, it shall operate, check and manage in accordance with instruction for diesel engine strictly.

Requirements on transporting girder vehicle of girder carrying

Woods or rubber blocks must be placed on the I- beam of steering wheel, which should be more than 40 mm with groove.

It must always keep the lubricity of friction of carrying steering wheel to ensure flexible rotation of the steering wheel. Smear butter when necessary.

Steadiness of Concrete Girder Loading

Common method of concrete girder loading is using gantry crane to lift the girder onto the vehicle, and place woods and rubber blocks on the I- beam steering wheel of the vehicle. Girder barycenter shall be right on the central line of the steering wheel or the vehicle. When barycenter of girder deviating from the center, it shall enable barycenter of concrete girder overlap the center.

After concrete girders are lifted on the vehicle, reinforcement measures must be taken. It must install inclined strut on both wings of the concrete girder and adjust screw rod for tightening. At the same time, it shall use four wires and 4 three- ton chain blocks to connect and tighten between concrete girder and hook at the end of steering wheel of transporting girder vehicle at four corners, ensuring balanced and stable consolidation of concrete girder and transporting girder vehicle. (More details please see the figures below).

Road Conditions and Radius of Turning Circle

Road for transportation should be smooth and solid without sedimentation phenomenon.

When the vehicle passes through the expansion joints, it shall process steel plate for mobile springboard. 10 mm thickness steel sheet with 25# I- beam reinforcement welded below is adopted. Processing quantity is four in general. When the vehicle runs on the incomplete road or bridge, it shall pay attention to the pavement pit, reinforcement on the surface and other barriers that are harmful for vehicle running. More details please see the figure attached.

Maximum turning angle of the vehicle is 20º, while the minimum turning radius is 18 meters.

As front and rear vehicles are equipped with steering gears and steering wheels, both vehicles can be controlled independently. Each vehicle has its own routine. Central position should be controlled to avoid touching the barriers.

For more information about heavy haulage trailers for saleand self propelled trailer, please feel free to contact us!

Other supplier products

	HEAVY DUTY TRAILER APPLICATION FOR WIND ENERGY	For the wind blade, its length is very long, till today some of them are over 100 m long, which has become the main feature different from other co...
	GIRDER BRIDGE TRAILER	Girder Bridge Traileris an indispensable category in the field of heavy cargo transportation. With the development of industry, especially the vigo...
	GIRDER CARRIER	GIRDER CARRIER Girder Carriercarrying capacities of 120T, 160T, 180T, 220T, 250T, and 300T that can be used directly to feed girder to bridge laun...
	EXTENDABLE TRAILER	The traditional low bed trailer can not meet the demand of long cargo transportation in many cases. As required, we design the extendable flatbed t...
	MODULAR TRAILER	A modular traileris normally used for transporting heavy loads over 80t. It is generally applicable to the medium and long-distance highway transpo...

供应产品

Same products

	Water Tank-Containers For Aquaculture Farming	卖方: WFH SG GROUP PTE LTD	fish farming water tankis designed for cultivating various seafood organisms, such as fish, shell...
	Specialised Container for Sale/Rent	卖方: WFH SG GROUP PTE LTD	Specialised shipping containersprovides a diverse range of products tailored to meet the specific...
	WFH Shipping Containers For Sale	卖方: WFH SG GROUP PTE LTD	WFH offers a wide selection of high-quality corten steel shipping containers for saleto meet your...
	WFH Shipping Containers For Rent	卖方: WFH SG GROUP PTE LTD	WFH is a reliable provider of comprehensive 40 shipping container for rentservices. Our offerings...
	Refrigerated Shipping Container for Sale/Rent	卖方: WFH SG GROUP PTE LTD	The new reefer container for saleis specifically designed for the transportation and storage of t...