Auto Rear View Mirror Housing Mold
Auto Rear View Mirror HousingMold
The car rearview mirror is an important part of car exterior parts, located on both sides of the car, is one of the most important exterior parts of the car. The rearview mirror of a car is a device used to allow the driver to observe the road conditions during driving, which can be said to be the driver's eyes. Automobile rearview mirrors are generally composed of mirror ring, base, mirror housing, bracket, rotating shaft, and other parts.
Precautions for Auto Rearview Mirror Housing Mold
The parting line of the plastic part is on the R, and the R is on the fixed and movable mold respectively. In order to avoid the parting line appearance of the visual surface, special attention should be paid to making the core side 0.05-0.1mm smaller to avoid mismatch of the plastic part.
The fixed and movable die stop should be designed with precise positioning. Avoid dislocation of fixed and movable mold cores and prevent the mismatch of plastic parts.
Because of the sharp edges of the Auto rearview mirror housing mold setting and the mold core plastic material position, must be taken care of to protect it during the mold making. It is best to use opaque tape to protect it to avoid gaps during transportation.
When designing an oblique slider with a core pulling along the Z-axis, it is necessary to pay attention to the slope of the bottom surface of the front end of the oblique slider to be greater than or equal to the angle of the bottom surface of the oblique slider seat to avoid undercutting.
The design of the cooling lines and spring of the inclined slider must be parallel to the angle of the core pulling of the inclined slider to facilitate the processing of the inclined slider.
The bottom of the wear block at the bottom of the inclined slider should be designed to be straight, and the wear block should be protruding to avoid interference with the B plate and the stroke stop of the inclined slider when the inclined slider moves backward.
Since the oblique slide block must be installed with the fixed mold core to save the jaws, the slider needs to be designed for the mushroom head positioning, and the design of the craft screw is also necessary to facilitate the installation of the fixed mold core and the oblique slide block to save the jaws.
We have types of injection molding dies for sale, if you have needs to buy injection moldproducts, please contact us.
在线联系供应商
Other supplier products
Auto Part Mold | With the vigorous development of the automotive industry, plastic auto part mold is also developing rapidly. 90% of auto parts are produced by inje... | |
Teeth Tray Mold | A dental impression is a mold removed from a tooth to diagnose and treat dental conditions. They are also used in forensic science. Impressions are... | |
Filter and Flow Limiting Apparatus | The family mold is used to produce injection parts for liquid filtration and flow monitoring and control systems. These accessories are custom... | |
Mouse Mold | One computer mouse usually includes these plastic parts: a bottom shell, an upper cover, a middle cover, a wheel, a base of wheel, a frame which co... | |
Plastic Spoon Mould | lastic spoon mainly used for eating, so it need to be heat resistant and non-toxic,and could meet the requirements of environmental protectionso, w... |
Same products
CSD16301Q2 TRANSISTOR MOSFET N-CH 25V 6SON TEXAS INSTRUMENTS | 卖方: ZK Electronic Technology Co., Limited | Part Number:CSD16301Q2 Description:CSD16301Q2 TRANSISTOR MOSFET N-CH 25V 6SON TEXAS INSTRUMENTS ... | |
CAPACITOR EEF-CX0J10CAPACITOR EEF-CX0J101R PANASONIC SMD SPEC POLYMER 100UF 6.3V SMD LF1R PANASONIC SMD SPEC POLYMER 100UF 6.3V SMD LF | 卖方: ZK Electronic Technology Co., Limited | Part name:EEF-CX0J101R Description:CAPACITOR EEF-CX0J101R PANASONIC SMD SPEC POLYMER 100UF 6.3V ... | |
Heavy Copper PCB Manufacturer | 卖方: Xinfeng Huihe Circuits Co., Ltd. | Heavy Copper PCB, pcb fabrication up to 12oz, large current, pcb circuitfabrication base material... | |
8 Layer ENIG Half Hole Custom PCB | 卖方: Xinfeng Huihe Circuits Co., Ltd. | Number of layers: 8 Surface finish: ENIG Base material: FR4 Outer Layer W/S: 4/3mil Inner lay... | |
4 Layer ENIG Impedance Control Half Hole PCB Electric Circuit Board | 卖方: Xinfeng Huihe Circuits Co., Ltd. | Number of layers: 4 Surface finish: ENIG Base material: FR4 Outer Layer W/S: 6/4mil Inner lay... |