hhcircuits.12
Half Hole & Through Hole Pcb
Through hole circuit board& half hole PCB, no copper burr residue or warpage in half hole, reduce connectors and save space, apply to Bluetooth module and Signal receiver products. HUIHE CIRCUITS PCB board with holesapply to Bluetooth module and Signal receiver products. Our PCB products have passed ISO9001/ISO13485/IATF16949/UL/RoHS/REACH certification.
Half Hole & Through Hole PCB List
2 Layer OSP Impedance Control Half Hole PCBChina
2 Layer ENIG Half Hole PCB
4 Layer ENIG Impedance Control Half Hole PCB Electric Circuit Board
2 layer ENIG impedance control half hole PCB
8 layer ENIG half hole custom PCB
4 layer ENIG impedance control half hole fr4 PCB
4 layer ENIG impedance control half hole PCB
4 layer LF-HASL half hole PCB
Production Process Of Metallized Half-Hole PCB
For the front inversion, to prevent the quality of the product and the need to make corrections in the later process, the production process of this type of board is processed according to the following process: a drilling (drilling, gong groove-plate surface plating-external Optical imaging-pattern plating-co-drying-half-hole processing-film stripping, etching, tin stripping-other processes-shape
Main Points Of Metallized Half-Hole PCB Production
The specific metallized PCB half holes are processed in the following way: all metallized half-hole PCB holes must be drilled in the pattern after plating, and one hole at the intersection of the two ends of the half-hole should be drilled before etching.
The engineering department formulates the MI process according to the process
The metal half-hole is the second-drilled half-hole drilled during the first drilling (or gong), after the image is plated, and before the etching. It is necessary to consider whether the copper will be exposed when the gong groove is shaped, and move the drilled half-hole into the unit.
he right hole is drilled first, and then the board is turned over (or mirrored) and the left hole is drilled to reduce the pulling of the copper of the inner hole of the half hole by the drill, resulting in the lack of copper of the hole.
The size of the drill nozzle for drilling the half hole depends on the spacing of the contour lines.
Draw the solder mask film, use the gong space as a stop point and open the window to increase 4mil treatment.
The Designer's Suggestion When Designing The Circuit
Change the distance from the edge line to the hole center. The general design is to place the hole center on the edge line and move the control center down. For example, the diameter of the hole is 1.4mm, the distance between the two holes is 2.54mm, and the board edge The distance between the line is 0.33mm from the center of the through hole, and the thickness of the plate is 0.6mm. The angle between the tangent to the cut point of the wall and the track of the milling cutter was 90 degrees before, but this time it is about 60 degrees. Because the board edge line is at a certain distance from the center of the through hole, the cutting angle of the milling cutter is changed, and the board thickness is extremely small, so the copper in the hole is not easily pulled out. The simultaneous improvement of small batch pcb design and production can greatly improve the production yield of PCB half-hole boards.
在线联系供应商
Other supplier products
 |
Industrial Control PCB | With the continuous development of the “pcb automationequipment + industrial robot operation” mode,The requirements for electronic and ... |
 |
New Energy PCB | Huihe Circuits is your ideal partner, providing you with electromechanical, green energy, renewable energy, PCB manufacturing services and solar la... |
 |
2 Layer Rogers LF-HASL PCB | Number of layers: 2 size: 184.2*158.9mm Surface finish: LF-HASL Base material: Rogers 4350B Minimum Line Width: 0.227mm Minimum Line Space: 0.... |
 |
10 Layer Impedance Control Resin Plugging PCB | Previous image Next image Number of layers: 10 Surface finish: ENIG Aspect Ratio: 8:1 Base material: FR4 Outer Layer W/S: 4/4mil Inner layer... |
 |
2 Layer OSP Impedance Control Half Hole PCB | Number of layers: 2 Surface finish: OSP Base material: FR4 Outer Layer W/S: 6/4mil Thickness: 1.0mm Special process: impedance control+half ho... |
Same products
 |
iFixes Solder Paste 138℃ 158℃ 183℃ 217℃ PCB BGA Chip Flux | 卖方: 深圳市维客修科技有限公司 | Description iFixes solder paste is138 is158 is183 is217 conductive silver paste for mobile phone... |
 |
DWDM Add and Drop Mux Demux | 卖方: Guangzhou Sintai Communication Co.,LTD | What Is OADM? The DWDMmultiplexercard launched by Sintai Communication Co., Ltd is generally use... |
 |
DCM | 卖方: Guangzhou Sintai Communication Co.,LTD | What Is Dispersion Compensation Fiber Dispersion Compensation Module (DCM) is designed to fix th... |
 |
Aggregation & Distribution System | 卖方: Guangzhou Sintai Communication Co.,LTD | Aggregation & Distribution System Sintai Aggregation & Distribution System offers 32*100... |
 |
CWDM Mux Demux | 卖方: Guangzhou Sintai Communication Co.,LTD | 4CH CWDM Mux Demux 01- 4CH CWDM DWDMMux Demux CWDM Coarse Wave Division Multiplexing (CWDM) Mul... |
