Auto Bumper Mould
The front and rear bumpers of the car are made of plastic, which not only maintains the protection function, but also has the characteristics of harmony and unity with the body shape, lightweight, and low fuel consumption. The plastic front bumper consists of three parts, namely the outer panel, the buffer material, and the cross member. The raw materials of the outer plate and the buffer material are all plastic, the beam is stamped into a U-shaped groove from a cold-rolled sheet, and the thickness of the cold-rolled sheet is about 1.5 mm. There are generally two types of materials used in bumper mold: polyester and polypropylene, and the molding process is generally injection molding.
Automobile Bumper Mold Manufacturing
Green Vitality is a professional automobile mold manufacturer and has rich experience in automobile bumper mold manufacturing.
The car bumper injection moulding designed by Green Vitality not only has the ability to reduce the injury of drivers and passengers during high-speed impact but also has the ability to protect pedestrians. Green Vitality uses an internal parting structure design for the bumper mold. Compared with the traditional outer parting structure design, the inner parting design has higher requirements on the strength of the mold. Correspondingly, the design concept of the bumper mold made by the internal parting structure is more advanced.
Basic Information for Auto Bumper Mould
Auto Bumper Mould Specification
Description Auto Bumper Mold
Plastic material PP
Mould cavity&core steel P20,2738,718H,738H,NAK80,SKD61,E420,etc.
Mould weight (T) 10T
Feeding System Cold runner/ Hot runner
Hot runner brand YUDO, HUSKYFISA, HASCO, MOLD-MASTER
Nos of Cavity 1*1
Manufacture time (day) 120 days
Mould life ≥500000
Packing Vacuum+plywood wooden box
Green Vitality Can Offer You with Auto Bumper Mould
Analysis: Through the analysis of material properties and product feasibility, such as wall thickness, deformation, plastic feeding position, etc., potential problems can be predicted in advance.
Communication: Maintain close communication with customers, and understand the functional requirements and precautions of products from the perspective of customers, such as requirements for weld lines, requirements for appearance, etc.
Design: Strict design review system and checklist check. Before design, during the design of the scheme structure discussion meeting, the designer will check himself according to the checklist; after design, review together with the manufacturing department.
Quality inspection: Quality inspection of each link to discover mass production problems in advance.
Project management: Each project is equipped with a project manager, who strictly follows the schedule to control the project cycle, and provides weekly progress reports and mold photos for each project so that customers can keep abreast of the status.
Service: From mold design to continuous mass production of products, we provide full life cycle service support.
After-sales service: continuous after-sales follow-up service, proactively providing mass production and processing technical consulting services.
Technical support: In the mass production process, if there is any problem with the mold, technical support will be provided unconditionally.
Why Are Auto Bumpers Made of Plastic Material?
Control costs
The bumper steel plate is replaced with plastic, the cost is greatly reduced, the production is convenient, and the plastic bumper is also very malleable, which can meet the bumper design requirements of various car models.
Realize lightweight
If a car is too heavy, it will greatly increase the fuel consumption requirements, and the increased emission pollution is not good for the environment. Nowadays, the emission of vehicle exhaust is becoming more and more stringent. From the root of the car, the weight of the body must be reduced. This is the development of the car. The trend is also to design plastic for fuel economy and environmental protection. The use of plastic bumpers will not only reduce fuel consumption but also improve performance.
Protect pedestrians
The plastic bar material is elastic and has better shock absorption and buffering capacity than steel plates. If it is still a steel plate, if you hit someone, the consequences will be serious. Then there is no need to go to the hospital, just go to the crematorium, and the design is made of plastic It can greatly reduce the damage caused by impact.
Anti-corrosion
Plastics have inherent advantages over metals. Metals are prone to rust and corrosion when exposed to water and air, which affects the appearance of cars. Plastics have good corrosion resistance, so there is no need to worry about rust.
With self-repair function
Usually, the bumper made of plastic material has little effect when driving. It has elasticity and can repair itself, leaving only a few small scratches. As shown in the figure, it may be restored to its original state once it is heated with hot water. Otherwise, the pits created by the impact cannot bounce by themselves and affect the appearance.
As a plastic injection factory, we can offer kinds of plastic injection moldfor sale, anything you need, please leave us a message.
在线联系供应商
Other supplier products
 |
Industrial Plastic Injection Mold | The injection molding part is replacing metal products in many fields of industrial applications to meet the requirement of lightweight industrial ... |
 |
Plastic Enclosure Mold For Electronic Device | In a Lego game, you will hold the laser, sit on the device, and shoot various targets. Since this game is mainly to meet the gaming experience of L... |
 |
Fan Mold | If the weight of each fan blade is not balanced, large vibration, high noise, and large wear of the rotating shaft will occur during high-speed rot... |
 |
Game Controller Mold | To increase the production efficiency, we need optimize the mold cooling system to shorten the cycle time. As a result, machining cost and time wil... |
 |
Soap Box Mold | Plastic soap is also made by plastic injectionmold, as it need dimensional stability, good apperance and good color performance, so we have to choo... |
Same products
 |
Medical Plastic Parts | 卖方: Packson Mold Co.,Ltd | Project Management To be a qualified medical plastic components manufacturer, the most advanced ... |
 |
PA66 GF15 Heat Stabilized (A2006C, A2016C) for Engineering Plastics | 卖方: Suzhou Anmei Material Technology Co., Ltd | PA 66 GF 15is a 15% glass fiber reinforced, heat-resistance, polyamide 66 resin for injection mol... |
 |
PA66 GF | 卖方: Suzhou Anmei Material Technology Co., Ltd | Anmei focuses on the production of modified engineering plastics. We have polyamide pa6 6gfmodif... |
 |
Nylon6 PA6 | 卖方: Suzhou Anmei Material Technology Co., Ltd | Other than fiber-reinforced pa6 polyamide, the unreinforced nylon type 6 produced by Anmei, one o... |
 |
Nylon 66 Pa66 With High Tensile Strength (A2307X01, A2317X01) for Engineering Plastics | 卖方: Suzhou Anmei Material Technology Co., Ltd | Using Polyamide 66 as the basic resin, the tensile strength of nylon 66 is obtained by blending a... |
