Processing Performance and Conditions of ABS Injection Molding
Ⅰ. ABS Injection Molding Processing Performance
(1) Because of the strong moisture absorption as well as high water content of ABS, the plastic parts that are made of ABS have low gloss and poor internal quality. As a result, ABS injection molding should be dried so that the water content is not more than 0.3%.
(2) ABS melt has obvious non-Newtonian properties. Increasing the molding pressure can significantly reduce the melt viscosity, and its viscosity will also decrease with the increase of temperature.
(3) ABS has a small molding shrinkage rate, and the shrinkage rate changes in the range of 0.3% to 0.8%, so the precision of plastic parts is high.
(4) ABS injection moldinghas good processing performance, and there are no special requirements for injection molding machines. Both general screw and plunger injection molding machines can be used, but multi-purpose screw injection molding machines have better product quality.
(5) In order to improve the quality, dimensional stability, surface gloss of plastic parts and eliminate residual internal stress when using screw injection mold tooling machine, it is more appropriate to control the injection volume at about 50% of the maximum injection volume.
(6) The viscosity of ABS melt is medium, better than PC and PVC, but worse than PS, so it is better to use straight-through nozzle.
(7) The main channel of the ABS mold is preferably conical, and the main channel should be short, generally about 50mm, and the longest should not exceed 100mm.
(8) The cross-sectional area of the runner must be large enough so that the molten material can fill the cavity before the runner solidifies and compact in the mold. The diameter of the section should generally be greater than 5mm, but not more than 10mm.
(9) The ejection force of the ejection mechanism of ABS should not be too large, otherwise the surface of the plastic part is prone to whitening.
(10) Although the shrinkage rate of ABS injection china plastic mouldingis small, it is easy to generate internal stress, so the plastic parts generally need to be heat treated, and the plastic parts can be treated in hot air at 70 ° C for 2 to 4 hours.
Ⅱ. Conditions for ABS injection molding temperature(1) Barrel temperature
ABS is an amorphous plastic with no obvious melting point, and the melt flow temperature is not too high. It has sufficient fluidity above 160 °C, but if the temperature is too high, it will not increase the fluidity. There are many varieties of ABS, and the barrel temperature of different varieties is different. The barrel temperature of general ABS is 180~230℃, the temperature of heat-resistant ABS is 190~240℃, and the temperature of flame retardant ABS is 170~220℃. The nozzle temperature is 20~30℃ lower than the barrel temperature.
(2) Mold temperature
The level of mold temperature has a great influence on the quality of plastic parts. During ABS injection molding, the mold temperature should be controlled within the allowable range. Generally, the mold temperature should be controlled at 50-70 °C.
(3) Injection pressure
The size of the injection pressure mainly depends on the structure and wall thickness of the plastic part. Usually, the injection pressure of general ABS is 50-70MPa, the injection pressure of heat-resistant ABS is 60-85MPa, and the injection pressure of flame-retardant ABS is 60-100MPa. If the flow resistance during filling is large, use a higher injection pressure. Conversely, use a lower injection pressure.
在线联系供应商
Other supplier products
 |
Injection Molding Service | As a china abs molding supplier, Keyplast has leading advantages in custom plastic molding industry, with rapid quotation, professional design, eff... |
 |
Injection Molding | Plastic Injection Molding Plastic injection molding is a method of making plastic products. The molten plastic is injected into the mold by pressu... |
 |
Plastic Injection Molding | What is plastic injection molding? Plastic Injection molding is a molding method that combines injection and molding. The advantages of plastic sma... |
 |
Injection Mold Design Engineering | Injection Mold Design Engineering Injection mold engineeringis a procedure at the first stage of injection molding process, which develops the inj... |
 |
Gardening Injection Molding | Keyplast brings every concept into a reality, not only for every client, but also for our own development in all areas, especially in gardening ind... |
Same products
 |
Medical Plastic Parts | 卖方: Packson Mold Co.,Ltd | Project Management To be a qualified medical plastic components manufacturer, the most advanced ... |
 |
PA66 GF15 Heat Stabilized (A2006C, A2016C) for Engineering Plastics | 卖方: Suzhou Anmei Material Technology Co., Ltd | PA 66 GF 15is a 15% glass fiber reinforced, heat-resistance, polyamide 66 resin for injection mol... |
 |
PA66 GF | 卖方: Suzhou Anmei Material Technology Co., Ltd | Anmei focuses on the production of modified engineering plastics. We have polyamide pa6 6gfmodif... |
 |
Nylon6 PA6 | 卖方: Suzhou Anmei Material Technology Co., Ltd | Other than fiber-reinforced pa6 polyamide, the unreinforced nylon type 6 produced by Anmei, one o... |
 |
Nylon 66 Pa66 With High Tensile Strength (A2307X01, A2317X01) for Engineering Plastics | 卖方: Suzhou Anmei Material Technology Co., Ltd | Using Polyamide 66 as the basic resin, the tensile strength of nylon 66 is obtained by blending a... |
