clear platinum cure silicone rubber jewelry molding high quality free sample
clear platinum cure silicone rubber jewelry molding high quality free sample
Description
High transparency, two-component silicone,platinum-curing/ addition-cure type, flowable, vulcanizes at room temperatureor heated temperature.
Can be used for a long time in the temperature range of - 65 ° C - 250 ° C and keep its soft and elastic properties.
Application
Suitable for mold making which request high transparency to see the mold’s inside details clearly, for example rapid prototyping, lost wax casting, jewelry molds, crystal molds and so on which also request the surface of the finished product shall be transparent and glossy.
Features& Advantages
²High transparency
²Food grade, FDA
²Low shrinkage
²Low viscosity
²Anti-deformation
²Not oily
²No bubbles
²Excellent flow levelingwhich will copy finest details and patterns from exquisite products.
²Durable with excellent tear and tensile strength, guarantee molding times
²Easily demolding
²High temperature resistance
²Resist aging, acid,alkali,corrosionand weather aging
Typical propertiesINI-Q640
|
PropertiesIndex |
Test Report |
|
|
Before Curing |
Appearance |
Transparentliquid |
|
Viscosity（cps） |
28000±1000 (Adjustable) |
|
|
Operating |
Mixing Ratio （By weight） |
1：1 or 10：1 |
|
Operating Time（25℃/min） |
30～40 (Adjustable) |
|
|
Curing time（hr,basically cured） |
2~4 (Adjustable) |
|
|
Curing time（hr, perfectly cured） |
12 |
|
|
After Curing |
Hardness (shore A) |
40±2 |
|
Tear strength (kN/m) |
15±0.5 |
|
|
Tensile strength (Mpa) |
6±0.5 |
|
|
Shrinkage (%) |
≤0.1 |
|
|
Elongation (%) |
320~360 |
|
|
Density (g/cm) |
1.02 |
|
Notes: Above data are only reference values, actual data is floating and adjustable.
Operation instructions
1.Mix part A and pars B evenly with 1:1 or 10:1 mixing ratio.
Notes: 1) Weigh the two parts exactly by electronic weight. For example, the operation time will be shorten after adding too much catalyst.
2)Mix part A and part B evenly. Otherwise the silicon rubber will be partly solidified which will make the finished molds meet a short life and
waste silicon rubber.
2.Vacuum pumping
Notes: 1) This step is not have to have, but it is best if there is one. It will discharge all air in the mixture successfully, so as to ensure that therewill be no bubbles in the finished mold.
2) This step is less than 10 minutes. Otherwise, itWill cause cross-linking reaction, and no more further steps will be available.
3. Pouring casting
Notes: We suggest to set the mold for another 12 hours after demould before put it into large production.
Notes: We suggest to set the mold for another 12 hours after demould before put it into large production.
Package
5KG, 20KG, 25KG and 200KG per drum.
(There are metal drum and plastic drum for your choice for 5KG and 20KG)
Shelf life
Twelve(12) months when stored under dry and cool place by original package under 25℃.
WhyChooseus
1.Powerfulfactorywithaproductioncapacityof8000perday, we are the more than 10 years factory in China, with excellent and stable quality.
2.High-endresearchanddevelopment(freesample)
BeingaleadingliquidsiliconemanufacturerinChina,wehaveaprofessionalR&DteamandQCteam(12experts)andourproductisRoHS,MSDS,ISO,REACH,ULapproved,sothereisnoneedtoworryaboutthequality.
3,Efficientservice
Wecanprovidefreetrainingofsiliconetechniqueandfreesiliconesamples.wehaveaprofessionalsalesteamwhowillsolveyourproblemspatiently.Besides,withefficientlogisticsdistributionsystem,youcouldgetyougoodsearlier.Last,goodaftersalesservice,webuildlongtermcooperationrelationship,oncethereisqualityproblem,wecouldsolverightaway.Moreimportantly,returnandexchangeareacceptedwhilequalityproblemsoccurred.
We can provide the free sample, more details about silicone rubber, pls contact Ms Lisa at:
Mobile/ Whatsapp/: +86 188 1670 2967
2967or A108059
E-mail:lisasilicone(at)
Twitter/Facebook:lisasilicone
在线联系供应商
Other supplier products
 |
双组分锡固化硅橡胶模具免费样品 | 1. ОписаниеДвухкомпонентный силикон, отверждаемый оловом, текучий, вулканизируется при комнатной температуре.Может использоваться в течение длитель... |
 |
food grade silicone rubber soft addition base liquid silicon insole | food grade silicone rubber soft addition base liquid silicon insole Description Two-component silicone,platinum-curing/ addition-cure type, flow... |
 |
Pad printing silicone rubber liquid raw material elastic material electronic | Pad printing silicone rubber liquid raw material elastic material electronic Description Two-component silicone, tin-curing, flowable, vulcanizes... |
 |
rtv2 liquid platinum cure silicone rubber molding high quality cheap price | rtv2 liquid platinum cure silicone rubber molding high quality cheap price Description Two-component silicone,platinum-curing/ addition-cure type... |
 |
UL 94 V0 grade silicone encapsulating potting compound sensors led pcb | UL 94 V0 grade silicone encapsulating potting compound sensors led pcb Description Two-component silicone,platinum-curing/ addition-cure type, f... |
Same products
 |
Easy-cleaning Silicone-Modified Waterborne UV Resin | 卖方: Guangzhou Human New Material Science and Technology Co., Ltd | LUV533 is a high-performance, silicone-modified hexafunctional waterborne UV resinengineered to d... |
 |
Water-based Soft-Touch Resin for Consumer Electronics | 卖方: Guangzhou Human New Material Science and Technology Co., Ltd | Water-based Soft-Touch Resinis an advanced coating material formulated to deliver a luxurious, ve... |
 |
Conformal Coatings | 卖方: Guangzhou Human New Material Science and Technology Co., Ltd | The conformal coatingsprovide good adhesion to metal, PCB and other substrates after curing at ro... |
 |
Metalized & Laser Transfer coating | 卖方: Guangzhou Human New Material Science and Technology Co., Ltd | Metallized and laser transfer coatingsare designed with sustainability in mind, ensuring minimal ... |
 |
Hydrophilic coatings for Air Conditioner | 卖方: Guangzhou Human New Material Science and Technology Co., Ltd | A water-based coating combination applied on the surface of aluminum foil, which forms a layer wi... |
