Superdurable polyester powder coatings with metallic finish MT-D2525 Brilliance
Product description
MT-D2525 Brilliance is a series of ultra-durable powder coatings specifically formulated without TGIC, intended for use on architectural aluminium and galvanized steel. Providing new levels of weathering resistance MT-D2525 Brilliance surpasses the performance of leading architectural powders. It offers significantly higher gloss retention and resistance to colour change combined with maximum film integrity to ensure long term cosmetic and functional protection. These powder coatings are classified in Family I – class 6c under standard NFT 36-005. The MT-D2525 Brilliance series being part of MT-D2525 range is awarded the prestigious Qualicoat Class 2 approval for ultra-durable architectural powder coatings and conforms to the requirements of EN12206 and EN13438 (high durability systems), GSB Master and AAMA 2604. Some colours may not be available in MT-D2525 Matt. Following RAL shades are excluded from the RAL families for Qualicoat Class 2: RAL 1003. 1028. 1033. 2004. 2011. 3015. 3017. 3018. 4001.
Powder properties
| Typical value |
|---|
| Chemical Type |
Polyester |
| Appearance |
Smooth |
| Density |
1.2 – 1.9 g/cm³, depending on colour |
| Gloss (60°) |
25 – 35 GU |
| Shelf life |
24 months below 30 °C |
| 12 months below 35 °C |
| Storage Conditions |
Under dry, cool (≤ 30°C) conditions (open boxes must be resealed) |
| Curing schedule |
15 – 35 min at 180°C |
| 12-25 min at 190°C |
| 10-20 min at 200°C (object temperature) |
Pre-treatment
For maximum protection it is essential to pretreat components prior to the application of the powdercoating. Aluminium components should receive a full multi-stage chromate conversion coating or suitable chrome-free pre-treatment or suitable pre-anodising to clean and condition the substrate. Detailed advice should be sought from the pre-treatment supplier. Galvanised steel requires surface preparation by either multi-stage pretreatment using either zinc phosphate or chromate conversion or controlled sweep blasting. Depending on the type of galvanizing, degassing or use of anti-bubbling additives may be required – follow the procedural advice of the pretreatment supplier. The products may also be used on cast or mild steel. For outdoor use MT- Redox PZ anti-corrosive primer over a correctly prepared substrate is recommended.
Application
Powders can be applied by manual or automatic electrostatic spray equipment. All powders can show small color differences from batch to batch, this is normal and unavoidable. Differences are more likely with special effect powders. We recommend the use of flat jet spray nozzles. The use of direct box feed equipment may not reproduce fully the finish of our color standard. The use of direct feed equipment, by pumping into the box, may not fully reproduce the expected rendering of our standard color. This equipment could be responsible for a heterogeneity of surface aspect (marble aspect). To ensure homogeneity of the finish, completely empty the contents of the box in a fluidized bin. Only one pass and one batch should be used for items that will be simultaneously visible after assembly/installation. For manual application it is essential to ensure that a uniform film thickness is applied. Unused powder can be recovered and recycled on most common equipment subject to normal controls on ratios of recycled to virgin powder.Different substrates (aluminium, steel, galvanized steel…), use of primer, and big changes in film thickness may give a different aspect (marble aspect). Bonded products have better application properties than blended products (more stable) but attention should still be paid to line settings in order to avoid “marble effect” and changes in aspect after recycling. A constant ratio between virgin and recycled powders should be fixed by the coater in order to achieve a consistent effect.Products with different codes should not be mixed even if same colour and gloss.
Test conditions
The results are based on mechanical and chemical tests which (unless otherwise indicated) have been carried out under laboratory conditions and are given for guidance only Testing has been determined under laboratory conditions using the following application properties and is for guidance only.
| Pre-treatment |
Chrome free Qualicoat/GSB approved pretreatmen |
| Substrate |
Aluminum (0.5-0.8 mm Al Mg1) |
| Curing schedule |
10 min at 200°C (object temperature) |
| Film Thickness |
60 – 80µm, ISO 2360 |
Mechanical tests
|
Typical value |
Method/standard |
| Adhesion |
Class 0 |
ISO 2409 (2 mm Crosshatch) |
| Erichsen cupping |
Pass Qualicoat class 2 requirements |
ISO 1520 |
| Flexibility |
Pass Qualicoat class 2 requirements |
ISO 1519 |
| Hardness |
>80 |
ISO 2815 (Buchholz hardness) |
| Impact resistance |
Pass Qualicoat class 2 requirements |
ISO 6272-2 (d/r) |
Chemical and durability tests
|
Typical value |
Method/standard |
| Chemical Resistance |
Generally good resistance to acid, alkalis and oil at room temperatures. |
|
| Sulphur Dioxide Resistance |
Pass 24 cycles– no blistering, loss of gloss or discoloration |
ISO 22479 |
Environmental and durability tests
|
Typical value |
Method/standard |
| Accelerated weathering |
≥90% Gloss retention, 1000 h |
ISO16474-2 |
|
≥50% Gloss retention, 600 h |
ISO 16474-3 QUV B 313 (GSB) |
| Acetic acid salt spray |
No blistering in excess of 2 (S2) according to ISO 4628-2. Infiltration <16 mm2 /10 cm, length of any single infiltration shall not exceed 3 mm., 1000 h |
ISO 9227 |
| Humidity |
No blistering in excess of 2 (S2) according to ISO 4628-2; the maximum infiltration at the cross is 1 mm, 1000 h |
ISO 6270-2 CH (Constant humidity) |
| Exterior durability |
Chalking – none in excess of minimum in ASTM D4214 Meets Qualicoat class 2 requirements after 3 years of Florida exposure Meet AAMA 2604 requirements after 5 years of Florida exposure |
ISO 2810 |
| Mortar resistance |
No effect after 24 hours |
EN 12206-1 |
| Wet adhesion |
No sign of detachment or blistering. Cross-cut value 0. Colour change is acceptable. |
Qualicoat/GSB |
If you're ready to take the next step or Request Free Samples, Leave your message below and we’ll reply soon. 20+ years of chemical manufacturing & export experience, a partner you can trust.
Other supplier products
|
|
Light Gray Sand Texture Powder Coating |
Introduction
It is athermosetting powder coating based on epoxy polyester resin with excellent smooth glossyand good flowout finishes. Its outstan... |
|
|
Trifluoromethane (CHF₃) |
Product Details
Product Names
Electronic Grade Trifluoromethane
High-Purity Trifluoromethane
Trifluoromethane (CHF₃)
Purity
Electronic Grade ... |
|
|
Garden powder coating |
Characteristics of powder coatings
1. The coating film is flat and smooth;
2. The paint film has good physical and mechanical properties, especia... |
|
|
General polyester coatings |
Introduction
ProductsPorducts DescriptionProduct StandardsWarranty
General polyester coatings
Outdoor used polyester resin and TGIC curing... |
|
|
4,4'-oxydiphthalic Anhydride(ODPA) CAS 1823-59-2 |
Introduction 4.4 '-oxybis-phthalic anhydride is a white to white powder organic substance that can be used to make polyimide resins.
Application 4... |
供应产品
Same products
