Standard durable polyester powder coatings
Product description
MT-D1036 Gloss is a range of powder coatings intended for use on architectural aluminium and galvanized steel. MT-D1036 Gloss has been specifically formulated without the use of TGIC. As part of the MT-D1036 series of architectural powders, MT-D1036 Gloss gives excellent exterior durability and colour retention and conforms to the requirements of all the major European architectural finishing standards. All MT-D1036 Gloss powders are lead-free and meet the requirements of GSB Florida 1. Qualicoat Class 1. EN12206. and EN13438 (formerly BS6496 &BS6497), and AAMA 2603.
| Qualicoat Approval | P-0773 (IT)
P-0991 (TR) P-0495 (ES) P-0352 (UK) P-0647 (CZ) P-0363 (DE) P-0747 (EG) P-0934 (RU) P-0143 (FR) |
| GSB Approval | 101k (gloss 85) |
| Resistance to Fire Approval | Classification: A2.s1.d0 with film thickness up to 120 µm (generic polyester D1036. D2525) according to EN13501-1 |
Powder properties
| Typical value | |
| Chemical Type | Polyester |
| Appearance | Smooth Gloss |
| Density | 1.2 – 1.9 g/cm³, depending on colour |
| Gloss (60°) | 80 – 90 GU |
| Shelf life | 24 months below 30 °C 12 months below 35 °C |
| Storage Conditions | Under dry, cool (≤ 30°C) conditions (open boxes must be resealed) |
| Curing schedule | 20 – 40 min at 170°C
10 – 20 min at 180°C 8 – 16 min at 200°C (object temperature) |
Pre-treatment
For maximum protection it is essential to pretreat components prior to the application of the powdercoating. Aluminium components should receive a full multi-stage chromate conversion coating or suitable chrome-free pre-treatment or suitable pre-anodising to clean and condition the substrate. Detailed advice should be sought from the pre-treatment supplier. Galvanised steel requires surface preparation by either multi-stage pretreatment using either zinc phosphate or chromate conversion or controlled sweep blasting. Depending on the type of galvanizing, degassing or use of anti-bubbling additives may be required – follow the procedural advice of the pretreatment supplier. The products may also be used on cast or mild steel. For outdoor useMT-PZ anti-corrosive primer over a correctly prepared substrate is recommended.
Application
Powders can be applied by manual or automatic electrostatic spray equipment. This product should be applied at minimum 60μm. All powders can show small color differences from batch to batch, this is normal and unavoidable. Bonded products have better application properties than blended products (more stable) but attention should still be paid to line settings in order to avoid “marble effect” and changes in aspect after recycling.
Products with different codes should not be mixed even if same colour and gloss. Different substrates (aluminium, steel, galvanized steel…), use of primer, and big changes in film thickness may give a different aspect.Applicators and fabricators are advised to use a single batch for parts that will be assembled together. Differences are more likely with special effect powders. For more information, it is suggested to read the Metallic Applications Guidelines. Clearcoats including tinted clearcoats cannot be applied directly on primers. Only fully opaque shades are suitable for application over primer.
| Application Method | Electrostatic |
| Recycling | For solid shades, unused powder can be reclaimed Unused powder can be reclaimed using suitable equipment and recycled through the coating system, but a minimum of 70% virgin powder should be used. |
Post application
For specific advice on the suitability of post coating processes such as bending or the use of sealants, adhesives, thermal break, cleaning etc. Please consult us.
Test conditions
The results are based on mechanical and chemical tests which (unless otherwise indicated) have been carried out under laboratory conditions and are given for guidance only Testing has been determined under laboratory conditions using the following application properties and is for guidance only.
| Pre-treatment | Chrome free Qualicoat/GSB approved pretreatment |
| Substrate | Aluminum (0.5-0.8 mm Al Mg1) |
| Curing schedule | 15 min at 180°C (object temperature) |
| Film Thickness | 60 – 80µm, ISO 2360 |
Mechanical tests
| Typical value | Method/standard | |
| Adhesion | Class 0 | ISO 2409 (2 mm Crosshatch) |
| Erichsen cupping | Pass 5 mm | ISO 1520 |
| Flexibility | Pass 5 mm | ISO 1519 |
| Hardness | >80 | ISO 2815 (Buchholz hardness) |
| Impact resistance | Pass 2.5 Joules reverse & direct (20 in lb) | ISO 6272-2 (d/r) |
Chemical and durability tests
| Typical value | Method/standard | |
| Chemical Resistance | Generally good resistance to acid, alkalis and oil at room temperatures. | |
| Sulphur Dioxide Resistance | Pass 24 cycles– no blistering, loss of gloss or discoloration | ISO 22479 |
Environmental and durability tests
| Typical value | Method/standard | |
| Accelerated weathering | ≥50% Gloss retention, 1000 h | ISO16474-2 |
| ≥50% Gloss retention, 300 h | ISO 16474-3 QUV B 313 (GSB) | |
| Acetic acid salt spray | No blistering in excess of 2 (S2) according to ISO 4628-2. Infiltration <16 mm2 /10 cm, length of any single infiltration shall not exceed 3 mm., 1000 h | ISO 9227 |
| Humidity | No blistering in excess of 2 (S2) according to ISO 4628-2; the maximum infiltration at the cross is 1 mm, 1000 h | ISO 6270-2 CH (Constant humidity) |
| Exterior durability | Chalking – none in excess of minimum in ASTM D4214 ≥50% gloss retention, Colour retention accords with GSB/Qualicoat 1 year(s) | ISO 2810 |
| No checking, cracking or loss of adhesion after tape pull and only slight chalking and fading after 1 year of Florida exposure | ||
| Mortar resistance | No effect after 24 hours | EN 12206-1 |
| Wet adhesion | No sign of detachment or blistering. Cross-cut value 0. Colour change is acceptable. | Qualicoat/GSB |
If you're ready to take the next step or Request Free Samples, Leave your message below and we’ll reply soon. 20+ years of chemical manufacturing & export experience, a partner you can trust.
在线联系供应商
Other supplier products
 |
Weather-resistant matte powder coating | Product description This series of products uses saturated polyester resin and acrylic resin as the main base materials to make thermosetting powd... |
|
|
Porcelain bamboo (green) MT-049/94945 | Introduction No. MT-049/94945 Color Porcelain bamboo (green) Surface Flat metal System Polyester Scope of applicatio... |
 |
Thermosetting flat powder coating | Product Introduction MT thermosetting flat powder coating adopts advanced polymer formula technology to form a dense and smooth coating through hi... |
|
|
High Reflectivity (Infrared Camouflage Cooling) Powder Series | Key Features & Specifications FeatureSpecification / Benefit Reflective Cooling Effect Reflects >90% of solar infrared radiatio... |
 |
Gasoline stripper inhibitor STD-20 | Gasoline stripper inhibitor STD-20 has the functions of anti-oxidation, anti-polymerization, cleaning and dispersing. This additive can effectively... |
Same products
 |
蓝翠鸟威尼斯灰泥涂料 墙面艺术灰泥 奢华质感 | 卖方: 中山蓝翠鸟新型环保材料有限公司 | 产品概述 蓝翠鸟威尼斯灰泥是商业空间与艺术场馆优选的艺术涂装材料，以精选天然石膏、环保水性成膜物质为原料，肌理独特且富有层次感，耐擦洗、易维护，适配商业展厅墙面、艺术画廊展墙、高端餐厅主题墙面... |
 |
蓝翠鸟天鹅绒纹理漆 室内设计高级感墙面装饰漆 | 卖方: 中山蓝翠鸟新型环保材料有限公司 | 产品概述 这是一款为空间注入情绪的涂料。天鹅绒般柔和的哑光表面，拥有安抚视觉和心灵的效果，能自然营造出宁静、安全、包裹感的氛围。特别适用于打造家庭阅读角、私人工作室、瑜伽室或任何您需要放松... |
 |
蓝翠鸟 水包砂 | 高弹抗裂 外墙专用涂料 | 卖方: 中山蓝翠鸟新型环保材料有限公司 | 产品概述 蓝翠鸟高弹抗裂水包砂，专为应对墙体细微开裂问题而设计。其涂层具备优异的弹性与延展性，能有效桥接并遮盖基层微裂缝，适用于易产生温度应力或轻微沉降的建筑外墙，提供持久的完美外观。 ... |
 |
蓝翠鸟 简修天鹅绒覆盖漆 | 旧墙翻新神器 遮盖涂料 | 卖方: 中山蓝翠鸟新型环保材料有限公司 | 产品概述 厌倦了老旧的墙面？蓝翠鸟简修天鹅绒漆是您的快速翻新方案。它拥有超强的遮盖力和附着力，能直接覆盖大多数旧墙面（如乳胶漆、腻子层），简化施工步骤。快速赋予老旧空间全新的天鹅绒质感与现... |
 |
商业空间用瓷砖胶——高效施工、耐磨耐用 | 卖方: 中山蓝翠鸟新型环保材料有限公司 | 产品概述 瓷砖胶是适用于商场、酒店、写字楼等商业空间的专业粘结材料，以优质水泥、级配石英砂、特种聚合物改性剂为原料，采用薄贴工艺实现高效贴砖，提升施工效率，且具备优异耐磨性，可承受高人流量磨损... |
