HDI PCB / BLIND&BURIED VIA HOLE PCB / BVH PCB

SPEEDAPCB has been focusing on the production of various PTH (plated through hole PCB), buried via hole PCB and blind via hole PCB, and HDI PCB prototype.

When it comes to blind and buried hole circuit boards, everyone thinks of HDI boards. Generally, there are more blind and buried hole circuit boards used in mobile s or navigation instruments. Such PCB boards require high technical content and accurate accuracy. Of course, the price is compared with other It is also high for multilayer circuit boards.

HDI high density interconnect pcb : 1 + n + 1, 1 + 1 + n + 1 + 1, 2 + n + 2, 3 + n + 3,

Features of Blind&Buried Via Hole PCB

HDI PCB

Blind Via Hole is the connection between the outermost circuit in the PCB and the adjacent inner layer with a plated hole. Because the opposite side cannot be seen, it is called blind pass. In order to increase the space utilization between the circuit layers of the board, blind holes come in handy. The blind hole is a via hole to the surface of the printed board.

Buried Via Hole, the connection between any circuit layers in the PCB, but there is no conduction with the outer layer, that is, there is no meaning of a via hole extending to the surface of the circuit board.

HDI PCB

The blind holes are located on the top and bottom surfaces of the circuit board and have a certain depth. They are used to connect the surface layer circuits to the inner layer circuits below. The depth of the holes generally has a prescribed ratio (aperture). This manufacturing method requires special attention, and the drilling depth must be just right. Failure to pay attention will cause difficulties in plating inside the hole. Therefore, few factories will adopt this production method. In fact, it is possible to drill the holes of the circuit layers that need to be connected beforehand, and then glue them together, but they need more precise positioning and alignment devices.

HDI PCB

This manufacturing process cannot be achieved by bonding the circuit boards and then drilling. It is necessary to perform the drilling operation at the individual circuit layer, firstly locally bond the inner layer, then perform plating treatment, and finally all the bonding. Because the operation process is more laborious than the original vias and blind holes, the price is also the most expensive. This manufacturing process is usually only used for high-density circuit boards, increasing the space utilization of other circuit layers.

HDI PCB

In the PCB manufacturing process, drilling is very important. The simple understanding of drilling is to drill the required via holes on the copper clad board, which has the function of providing electrical connections and fixing devices. If the operation of the via is caused by incorrect operation, the device cannot be fixed on the circuit board, which will affect the use of the circuit board, and the entire board will be scrapped. Therefore, the process of drilling is very important.

Parameters of Blind&Buried Via Hole PCB

Items
Max board size		580X700mm
Boar Material		FR-4,Aluminum, High Tg FR4,CEM3,etc.
Min trace width/ space (inner layer)		4mil/4mil(0.1mm/0.1mm)
Min PAD (inner layer)		5 mil(0.13mm)
Min thickness(inner layer)		4 mil(0.1mm)
Inner copper thickness
Outer copper thickness
Finished board thickness
Board thickness tolerance control	±0.10 mm	±0.10 mm
	±10%	±10%
	±10%	±10%
Inner layer treatment		brown oxidation
Layer count Capability		1-30 LAYER
alignment between ML		±2mil
Drill hole diameter
Aspect ratio of plated hole		10:01
Hole precision		±2 mil(±0.05mm)
tolerance for Slot		±3 mil(±0.75mm)
Hole diameter tolerance(PTH)		±3 mil(±0.075mm)
Hole diameter tolerance(NPTH)		±1mil(±0.025mm)
Max Aspect Ratio for PTH		8:01
Hole wall copper thickness		15-50um
Alignment of outer layers		4mil/4mil
Min trace width/space for outer layer		4mil/4mil
Tolerance of Etching		+/-10%
Thickness of solder mask		on trace
Thickness of solder mask	at trace corner	≥0.2mil(5um)
Hardness of solder mask	On base material	≤+1.2mil
	6H	Finished thickness
Alignment of solder mask film		±2mil(+/-50um)
Min width of solder mask bridge		4mil(100um)
Max hole with solder plug
Surface treatment		HAL (Lead or Lead free), immersion Gold, Immersion Nickel, Electric Gold finger, plated Gold, OSP, Immersion Silver.carbon oil,etc.
Max Nickel thickness for Gold finger		280u"(7um)
Max gold thickness for Gold finger		30u"(0.75um)
Nickel thickness in Immersion Gold		120u"/240u"(3um/6um)
Gold thickness in Immersion Gold		2u"/6u"(0.05um/0.15um)
Impedance control and its tolerance		50±10%,75±10%,100±10% 110±10%
Trace Anti-stripped strength		≥61B/in(≥107g/mm)
bow and twist

We provide printed circuit board supplies,hdi pcb board，hdi printed circuit boards，hdi pcb prototype，hdi circuit boards，high density interconnect pcb，high density pcb，buried via pcband buried vias pcb，RFQ today.

Other supplier products

	A NEW TYPE OF WIRE BOARD——RIGID FLEX PCB	Speedapcb - The PCB design companyin China, established in 2014, is located in Changsha, Hunan Province. The company focuses on high-speed PCB desi...
	Blank PCB	Speedapcb - The pcb supplierin China, established in 2014, is located in Changsha, Hunan Province. The company focuses on high-speed PCB design, pr...
	High-frequency PCB	High-frequency PCB is advancing to the trend of high speed, low consumption, small volume, and high anti-interference ability, which demands many n...
	WIRING ON THE DOUBLE-SIDED BOARD——DOUBLE SIDED PCB	There are wiring on both sides of thedual layer PCB, but to use the wires on both sides, you must have a proper circuit connection between the two...
	SPEEDA PCB BOARD PRODUCT	Speedapcb - The pcb supplierin China, established in 2014, is located in Changsha, Hunan Province. The company focuses on high-speed PCB design, pr...

供应产品

Same products

	Single side Anti-static PET Film	卖方: 00000	Single side Anti-static PET Film Anti-static PET Film Firsta Group is a professional manufa...
	film manufacturers	卖方: 00000	film manufacturers As one of the earliest film manufacturers in China, Firsta Group has the ...
	BOPP Film	卖方: 00000	BOPP Film Clear/Transparent BOPP Film Transparent / Clear Top Coated BOPP Film is made with...
	PET Siliconized Release Liner	卖方: 00000	PET Siliconized Release Liner PET Siliconized Release Liner Firsta Group is the earliest ma...
	Matte Metallized PET Film	卖方: 00000	Matte Metallized PET Film Matte Metallized PET Film (matte polyester film), is also known as ...