Drone Battery
The next part of your drone is your esc battery. Modern RC drones use lipo batteries, which have a good power to weight ratio and can discharge a large amount of current very quickly. Choosing the correct Lipo RC quadcopter battery for your drone involves many factors, and you must first have an idea of the voltage and amp requirements of the motor/prop combination that you intend to use. There are a number of factors to consider when it comes to choosing a battery pack. Before making a purchase, think about these points: * Voltage * Capacity * Weight * Physical Size * Connector * Discharge * Charging Rate Lipo Drone Battery Voltage (S) All Lithium Polymer cells have a nominal voltage of 3.7v per cell. When fully charged a LiPo cell should be 4.2v and when discharged it should never be below 3v. You will notice that LiPo packs are made up of layers of multiple cells. A 1S = 1 cell (3.7v). If the LiPo pack is listed as being 3S this means it is 3 cells x 3.7v (per cell) which is 11.1v (3s 11.1v lipo battery). It has 3 layers of 3.7v each. The rating for each cell is always referenced by its nominal voltage (3.7v), NOT the maximum voltage (4.2v). Capacity (mAh) This is usually the biggest or most obvious rating shown on the LiPo pack and is measured in mAh (Milliamp/hour) or Ah(Amp/hour). The capacity is an important factor to consider. Think of capacity (mAh) as the amount of fuel in your car’s fuel tank. A higher capacity tank will run your car for longer. 55 amps is the maximum safe current a motor can draw from this battery. The mah rating: 2200mAh is 2200 milliamp hours or 2.2 amp hours. That is the amout of energy the battery can hold. This battery will give 2.2 amps of current for one hour. Or 4.4 amps for 1/2 hour, or 8.8 amps for 15 minutes. Weight A 25c 2000mah Lipo battery can weigh from 170 grams to 270 grams. When you look to buy a battery, weight should be one of the thins you look at. Some 1600mah batteries weigh as much as some 2200mah batteries. A batteris has a huge effect on the planes power to weight ratio. Two extra ounces will make a big difference in your planes performance. Physical Size of TTF Longest Lasting Drone Battery For a battery to be right for your model it must fit within the model’s battery compartment. Not all batteries are the same size. While most manufacturers try to stay consistent in sizing, the dimensions can still be quite a bit different. Sometimes a 2mm difference in size might keep it from fitting in your model. Discharge (C) Discharge is the amount of power the battery can supply your power system. The ‘C’ rating is an multiplication of the capacity. Example: A 20C battery can discharge at 20 x 2,000mAh which is 40,000mAh or 40Amps. This is an important number to consider. It’s always good to use a wattmeter to measure the demand of your system. The millamp hours divided by 1000, times the C rating, equals the maximum continuous discharge amperage the battery is capable of sustaining. That’s mah/1000 x C = Amps. So 2200mah/1000 x 25C = 55Amps. The Charge Rate Some batteries will display a ‘C’ rating for charging. MOST batteries are rated at a 1C charge rate. The formula is this: XXXX mAh / 1000 x (Charging C rating) = XX amps For example: If you had a 2200mAh LiPo pack with a charge rating of 2C you would not want to charge the battery at rate more than 4.4 amps. It’s the lower amperage you charge your batteries, the longer they will take to charge. However, a slower charge is always better for the health of your battery. If you have the time… take it slow. If you can’t find charge rating on your battery, then play it safe and charge at 1C. Hard or soft? Normally LiPo batteries come in two different forms: as soldered packs wrapped in shrink wrap or as so called hardcase packs that feature an outer plastic box to protect the cells. If you just bash or race non-sanctioned races softcase (shrink-wrapped) packs are ok as long as you make sure that there is no possibility to damage them during use. Damage can be done by rocks, stones, wood and basically everything that you can find off-road. In this case hardcase packs are the way to go. When your model is equipped with an enclosed diy drone battery compartment shrink-wrapped are ok too. Shenzhen TitanFlying Technology Co., Ltd is a high-tech enterprise and professional Aero-Model manufacturer that unifies product design, research development, production, marketing and customer service. Our main product are uamanned aerial vehicle, including professional drones and consumer drones, as well as DIY components for drones.
Other supplier products
|
|
DIY Components |
The 5 Main Areas of DIY Drone Parts
Once you’ve decided on the type of DIY drone you want to build (e.g. quadcopter, hexacopter, etc.), you&r... |
|
|
AG Drone T1 Flight Controller |
Shenzhen TitanFlying Technology Co., Ltdis not an easy task to order or purchase from distant supplier, especially in international trade. This is ... |
|
|
Drone Charger |
Over the years we've seen continuous improvements in battery technology and I'm sure further improvements are on the horizon!
Since all our dron... |
|
|
TTF M1 RC Mini Drone Quadcopter |
Light-integral-streamline fuselage design
Self- stabilization technology
Unique fan blade design
Strong anti-break capacity
Mini drone M1-Qua... |
|
|
Aerial Drone Battery |
Good Lipo battery
Longest flight time
RC battery
RC Quadcopter Battery
Most pilots are all want to get a long flight time, but almost drones only... |
供应产品
Same products
