Traceable Rodders Copper cable in rod

TRACEABLE DUCT RODDER containing metal lines, can be used to detect equipment easily detect the direction of the pipeline, as well as the location of the TRACEABLE DUCT RODDER .

We can generate the TRACEABLE DUCT RODDER has two kinds, one is to be able to carry the monitoring function, one kind is the individual tracking function. The difference between the two is that with a probe into the function of a video wire inside, and a power cable, you can head the head to install the head, in order to view the situation in the pipeline. A bare copper wire can be used to locate and track the position of the TRACEABLE  DUCT RODDER in a single probe function.

 

The traceable duct rodders are available in 8mm-16mm diameter. Detectable duct rods are used to find, follow and accuratelymap the duct route without digging or trenching. The traceable duct rod is used in conjunction with both a signal transmitter and a receiver. The easily identifiable signal is transmitted along the entire length of the duct rod.

The  traceable duct rod has an 18 AWG copper wire, almost twice the size of the competition, in the center of the fiberglass core. The copper wire is also connected to the end fittings so the transmitter leads canmake a direct connection to the copper wire. The female end fitting provides the attachment point for the transmitter's lead connection. The other transmitter lead is connected to a stake driven into the earth. The direct connection of the signal to the copper wire provides themost effectivemethod of signal transmission.

Roddiameter:φ6mm,φ8mm,φ9mm,φ10mm,φ11mm,φ12mm,φ13mm,φ14mm,φ15mm,φ16mm.Rod length:80m,100m,120m,150m,200m,250m,300m,350m,400m,500m.

Rod selectIon   

Which is the right rod diameter for any given application? The rod selection is usually governed by several factors including:

The size of ducting it is to be pushed through

The distance the rod is to be pushed

The number and tightness of bends in the ducting

If the ducting is already occupied by cable

When being pushed through the duct, any rod will tend to form “sine waves”, hitting the wall of the duct at certain intervals.

Each time the rod comes in contact with the wall of the duct, it causes friction. The friction will build and eventually prevent the rod from being pushed any further. Small rod in large duct will make more frequent contact with the ducting; the same rod in smaller duct will make less frequent contact and therefore less friction so it can be pushed further. Large rod in small ducting is a good situation, but reduced flexibility of the rod may cause increased friction in the tighter bends.

Rod

Tensile Strength

of Rod

Minimum Bend

Radius

Typical Max.

 Duct Dia

 Push or Pull

 

2,300 lb

105mm

50mm

100m

6

5800lb

180mm

60mm

150m

8

7,700 lb

260mm

80mm

200m

9

8,580 lb

300mm

100mm

250m

10

9850 lb

360mm

150mm

300m

11

11,000 lb

400mm

200mm

350m

12

13,000 lb

450mm

250mm

400m

13

17500 lb

510mm

300mm

450m

14

19500 lb

560mm

350mm

500m

15

23200 lb

610mm

400mm

550m

16

25120 lb

660mm

450mm

600m



在线询价

至: Bazhou WanQi Power Tools Factory
Your E-mail:
消息正文:


Send to other suppliers

Other supplier products

Resin Cable Jointing Kits for Copper and Aluminium Cables
Resin Cable Jointing Kits for Copper and Aluminium Cables Scotchcast Resin Cable Joint Kit Product introduction: Cable Joint as an important connection point of the whole power supply network, its run...
5mm,6mm,8mm,9mm,10mm Duct Rodder Multiple diameter
5mm,6mm,8mm,9mm,10mm Duct Rodder Multiple diameter Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to ...
Traceable Rodders Copper cable in rod
Traceable Rodders Copper cable in rod TRACEABLE DUCT RODDER containing metal lines, can be used to detect equipment easily detect the direction of the pipeline, as well as the location ...
cotchcast Resin Cable Joint Kit
cotchcast Resin Cable Joint Kit Scotchcast Resin Cable Joint Kit Product introduction: Cable Joint as an important connection point of the whole power supply network, its run...
Tuf Rodder Diameter 5mm to 15mm
Tuf Rodder Diameter 5mm to 15mm Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to ...
供应产品

Same products

客户要求的玻璃钢穿线器4mm-16mm
客户要求的玻璃钢穿线器4mm-16mm 卖方: 霸州市德派尔电力工具厂 产品规格 对于任何给定的应用来说,哪个是正确的棒直径? 杆的选择通常受多种因素的影响,包括: 管道的推进大小推杆的推进距离,管道弯曲的数量和密度,管道是否已经被电缆占用。 我们提供各种尺寸的风管...
管道电线杆管道电缆敷设工具
管道电线杆管道电缆敷设工具 卖方: 霸州市德派尔电力工具有限公司 玻璃纤维导管Rodders 3/8“(10mm)直径 3/8“(10毫米)标尺具有34”直径的存储篮,可以舒适地存储高达800英尺的玻璃纤维杆。 标准Ruf棒...
专业制造商电缆穿线器
专业制造商电缆穿线器 卖方: 霸州市德派尔五金机具有限公司 我们重视我们的玻璃纤维风管管道的质量和货物的服务。 根据产品的不同规格, 我们会在1年到3年不等的产品质保期内作出,如果在质保期内出现质量问题,我们会为客户无常更换新产品而支付由此产生的运输费用。
12mm电缆穿线器
12mm电缆穿线器 卖方: 霸州市德派尔五金机具有限公司 介绍 如果您是管道买家,请选择我们作为您的供应商,这将是非常正确的。 我公司生产的管道机已有12年的历史,我们生产不同直径的管道机头,直径范围从3mm到15mm,长度为15mm。管径60m,10...
金属玻璃钢穿线器专业生产厂家供应
金属玻璃钢穿线器专业生产厂家供应 卖方: 霸州市德派尔电力工具厂 管道舵杆7/16“(11毫米)直径 7/16英寸(11毫米)杆配备我们最大的框架与40“直径的存储篮,可容纳1500英尺的7/16”玻璃纤维杆。 标准Ruf棒...