4 Pins Passive Infrared Sensor BL412 for Alarm System
Overview
Senbais the specialist PIR manufacturer for more than 15 years. We are the most advanced factory with complete categories. With strong R&D center, there are digital type and analog type, dual elements and four elements for you choose. The market cover domestic market, Korean, Amertica, Turkey and Europe.
Senba PIR sensor alarm systemis passive infrared type sensor. Working temperature is -20~ 85℃. There are 3type for PIR sensor, 3pins, 4pins, 6pins. For 3 pins type, 2s not adjustable. For 4pins, delay time adjustable. For 6pins, delay time, sensitivity, lighting adjustable.
Featuresof motion detector alarm
Robust Design Against False Starts
Low Curvature Lens
Technical Data
|
Characteristics |
Symbol |
Unit |
Remarks |
||
|
Supply Voltage |
VDD |
-0.3 |
V |
||
|
Working Temperature |
TST |
-20 |
85 |
°C |
|
|
Into |
-100 |
100 |
mA |
||
|
Storage Temperature |
TST |
-40 |
125 |
°C |
|
Characteristics |
Symbol |
Type |
Unit |
Remarks |
||
|
Supply Voltage |
VDD |
3 |
V |
IR = 0.5mA |
||
|
Working Current |
IDD |
9 |
11 |
μA |
||
|
Sensitivity |
VSENS |
90 |
μA |
|||
|
Output REL |
||||||
|
Output Low Current |
InOL |
10 |
mA |
VOL<1V |
||
|
Output High Current |
1NC |
-10 |
mA |
VOL>(VDD-1V) |
||
|
Lock time |
TOL |
s |
||||
|
On-time |
TOH |
2 |
3600 |
s |
||
|
ONTIME |
||||||
|
Input voltage |
0 |
VDD |
V |
0Vto ¼ VDD |
||
|
Input Bias Current |
-1 |
1 |
μA |
|||
|
Oscillator & Filter |
||||||
|
Low pass filter cut-off frequency |
7 |
Hz |
||||
|
High pass filter cut-off frequency |
Hz |
|||||
|
Oscillator frequency on Chip |
FCLK |
64 |
kHz |
|||
|
Interior Block Diagram |
||||||
Application
Intelligent security- burglar alarm
Wireless infrared detection alarm, uses advanced signal analysis and processing technology. When the intruder enters through the detection area, it sends alarm signal to control panel.
The PIR motion alarmis suitable for home, residential area, factory, shopping mall, warehouse, and offices.
FAQ
The sensor is called passive because it doesn't emit light to get measurements. The sensor in PIR is actually split into two parts. The reason for that is to measure motion. ... The sensor is also sensitive enough to even detect IR radiation source movement while the object is already in it's field of view.
Most low-cost motion detectors can detect up to distances of at least 15 feet (4.6 m).
在线联系供应商
Other supplier products
 |
PIR Sensor Module | Owning very strong R&D Center, Senba can research and develop the passive infrared sensorindependently. Among those chinese pirsensor manufactu... |
 |
Low Power Consumption Infrared Motion Sensor for Lighting G2X2 | Overview G2X2is quad elements type products. With same horizontal and vertical detection angles. It is widely used in ceiling light. PIR sensors ... |
 |
HDPE Pir Motion Detector Lens S9006 for PIR sensor Module | Areb you looking for motion sensor lens replacement? Overview According to your case color, we can design difference color of the fresnel lens. ... |
 |
Low Distortion Coupling Linear Optocoupler LCR - 0203 Series for Volume Control and Electrical Coupling | Overview Optocoupler is an electronic component that transfers electrical signals between two isolated circuits by using light. It is widle used i... |
 |
LDR Photoresistors | Huge Diam 20mm Photoresistor φ20series for Led DimmerOverviewA photoresistor (or light-dependent resistor, LDR, or photo-conductive cell) is a ... |
