Portable Surface Roughness Tester SRT6200
Model:SRT6200
1.FEATURES
1.FEATURES
This instrument is compatible with four standards of
ISO, DIN, ANSI and JIS and is widely used in production
site to measure surface roughness of various
machinery-processed parts, calculate corresponding
parameters according to selected measuring conditions
and clearly display all measurement parameters.
When measuring the roughness of a surface, the
sensor is placed on the surface and then uniformly
slides along the surface by driving the mechanism
inside the tester. The sensor gets the surface roughness
inside the tester. The sensor gets the surface roughness
by the sharp built-in probe. This roughness causes
displacement of the probe which results in change of
inductive amount of induction coils so as to generate
analogue signal, which is in proportion to the surface
roughness at output end of phase-sensitive rectifier.
The exclusive DSP processes and calculates and then
outputs the measurement results on LCD.
* Very easy to operate
* Multiple parameter measurement: Ra, Rz
* Highly sophisticated inductance sensor
* Built-in lithium ion rechargeable battery and control
circuit with high capacity
* Small in size, light in weight and easy to use
* Can communicate with PC computer for statistics,
printing and analysing by the optional cable and the
software for RS232C interface.
*Manual or automatic shut down. The tester can be
switched off by pressing the Power key at any time.
On the other hand, the tester will power itself off
about 5 minutes after the last key operation.
2.SPECIFICATIONS
Display: 4 digits, 10 mm LCD, with blue backlight
Parameters: Ra, Rz
Display Range
Ra: 0.05-10.00um/1.000-400.0uinch
Rz: 0.020-100.0um/0.780-4000uinch
Accuracy: Not more than 10%
Fluctuation of display value: Not more than 6%
Sensor :
Test Principle: Inductance type
Radius of Probe Pin: 10um
Material of Probe Pin: Diamond
Measurement Force of Probe: 16mN(1.6gf)
Probe Angle: 90°
Vertical Radius of Guiding Head: 48mm
Maximum driving stroke: 17.5mm/0.7inch
Cutoff length (l): 0.25mm / 0.8mm / 2.5mm optional
Evaluation length: 1~5 cut off optional
Driving speed:
sampling length = 0.25mm Vt=0.135mm/s
sampling length = 0.8mm Vt=0.5mm/s
sampling length = 2.5mm Vt=1mm/s
returning Vt=1mm/s
Resolution : 0.001μm if reading <10μm
0.01μm if 10μm≤reading<100μm
0.1μm if reading ≥100μm
Power Li-ion battery: rechargeable
Operating conditions: Temp. 0-50℃
Humidity <80%
Size:140x57x48 mm (5.5x2.2x1.9 inch)
Weight: about 420 g
Attachment:
Weight: about 420 g
Attachment:
Standard Sensor RP-100
Groove Stylus SRP-110
curvature Probe SRP-120
Extension Rod SER-150
Mesurement Stand SRS-1
Standard Sample Plate SSP-180
Cable and Software for RS-232/USB)
Bluetooth interface
Groove Stylus SRP-110
curvature Probe SRP-120
Extension Rod SER-150
Mesurement Stand SRS-1
Standard Sample Plate SSP-180
Cable and Software for RS-232/USB)
Bluetooth interface
在线联系供应商
Other supplier products
Wheat Flour Moisture Meter TK100S | High Frequency moisture meter MS350A is used for measuring moisture content of soil ,silver sand, chemical combination powder, coal powder and othe... | |
Digital Textile Moisture Meter DM200T | DM200T Textile moisture meter is a high-performance and digital moisture testing equipment by our company based on introduction of foreign advanced... | |
High Accuracy Temperature Meter TM1000 | TM1000 High Precision Thermometer Features: Platinum sensor insures linear response and high accuracy across the entire range Meter range -200.00... | |
Leeb Hardness Tester HM-6561 | 1.1 Typical Applications * Die cavity of molds * Inspection of bearing and other mass produced parts on a production line * Failure analysis of pre... | |
Wheat Flour Moisture Meter TK100S | High Frequency moisture meter DM300 is used for measuring moisture content of soil ,silver sand, chemical combination powder, coal powder and other... |