Automobile seat belt fixed point test bench-QINSUN
Applicable standards:
National mandatory standards:
GB 15083-2006"Automobile seats, seat fixtures and headrests strength requirements and test methods"
GB 14167-2006/2013"Car Seat Belt installation Fixed Point"
GB 11550-2009"Automobile seat headrest strength requirements and test methods"
GB 13057-2003/2014"Strength of passenger seats and their vehicle fasteners"
GB 14166-2013"Seat belt, restraint system, Child restraint System for Motor Vehicle Occupants ISOFIX Child Restraint System"
International Standards and regulations:
Eu ECE R14Uniform Regulation on the approval of Vehicles with regard to seat belt fixing Points
Eu ECE R17Uniform Regulation on the approval of vehicles with regard to seats, seat fixation points and headrests
Eu ECE R80（specific terms may vary from version to version）
FMVSS 207Seating System
FMVSS 210Seat Belt Assembly Fixing Point
FMVSS 225Child Restraint System Fixed Point
Enterprise standard:
For example, the test requirements of the strength of the seat system and the strength of the seat belt fixing point in the EP development standard of the German Volkswagen company.
SAE J 384Stationary Point Test Code for Seat Belts in Motor Vehicles
SAE J 385, Motor Vehicle Seat Belt fixed point performance requirements, etc.
Main parameters:
The main parameters of the car seat belt fixed point test bench may vary from model to model and manufacturer, but usually include the following aspects:
Load measuring range:
It is generally 030kN （multi-channel, such as 6 channels） or 015kN （less channel, such as 3 channels）。 This range can cover the strength test requirements of most car seat belt anchorage points.
Control accuracy:
For the force measurement control system of 0——30kN, when the measurement and control load is 5kN——30kN, the control accuracy is the standard value of ±200N; When the measurement and control load is 0——5kN, the control accuracy is the standard value ±100N.
For the 0-15kN force measurement control system, the control accuracy is similar, but the value is reduced.
Hydraulic cylinder number and load:
The number of hydraulic cylinders may vary depending on the design of the test stand, for example, a nine-channel test stand may be equipped with nine hydraulic cylinders.
The load capacity of each hydraulic cylinder also needs to meet the test requirements, such as the load capacity of 3T.
Travel and loading speed:
The stroke of the hydraulic cylinder is usually longer, such as 1000mm, to accommodate different sizes of seats and seat belt fixing points.
The loading speed can reach the pre-set output in a specified time, such as 2 seconds or less.
Loading force holding time:
The load force holding time can be adjusted according to the test requirements, such as 0.2s to 120s stepless.
在线联系供应商
Other supplier products
 |
Tumble dryer-QINSUN | Scope of Application Used for the drying process in theTextile Testing - Home Laundering and Drying Proceduresstandard and other textile testing e... |
 |
Geomembrane Environmental Stress Cracking Resistance Tester | Scope of application: The stress cracking strength of polyolefin geomembrane was measured and evaluated by notch constant load tensile test. Durin... |
 |
Automotive Wires Ozone Aging Chamber | Standards ISO 6722: Road vehicles – Electrical cables – Dimensions and test methods. SAE J1128: Low-voltage cables for automotive... |
 |
Car seat foam performance tester | Applicable standards: GB/T 6670-2008"Determination of falling ball resilience of soft foam polymeric materials" : This standard specifies the test... |
 |
Automotive wire cyclic bending testing machine | StandardThis testing machine aligns with global automotive industry standards for wire harness reliability, includingISO 6722(Road vehicles –... |
Same products
 |
Air Intake Filter Test System | 卖方: Standard Groups | The Air Intake Filter Test System is designed for testing industrial air filters and engine air f... |
 |
Mattress Spring Fatigue Tester，ASTM D3574 ，how to test mattress for sagging | 卖方: Standard International Group (HK) Limited | The King Size Foam Fatigue Tester is a single-station pneumatic fatigue testing system designed f... |
 |
Mattress Rollator，ASTM F1566 ，Mattress Durability Tester，Mattress Fatigue Tester | 卖方: Standard International Group (HK) Limited | The Mattress Rollator is a laboratory durability testing system designed to evaluate the long-ter... |
 |
HD2 Pneumatic Foam Fatigue Tester，ISO 3385，Foam Fatigue Testing Machine | 卖方: Standard International Group (HK) Limited | The HD2 Pneumatic Foam Fatigue Tester is a heavy-duty, single-station laboratory testing machine ... |
 |
VW Heel Abrasion Tester，ISO 4649 ，Heel Performance Testing Machine | 卖方: Standard International Group (HK) Limited | The VW Heel Abrasion Tester is designed to evaluate the wear resistance of floor covering materia... |
