Thermal Protective Performance Tester (TPP) - Test Equipment

The Thermal Protective Performance (TPP) Test Device was developed to measure the time elapsed for convective and radiant heat to penetrate through a protective composite fabric system - measuring the resulting damage to human skin.

Standards：

BS EN ISO 6942. EN 366. EN 407. ISO 11612. ASTM F1939. ASTM F2702. NFPA 1971. NFPA 2112. GB 38543. GB/T 38306

Feature：

Industrial personal computer with analysis software is suitable for severe testing conditions.

Automatic calculation for heat transmission factor and radiant heat transfer index.

Sample holder with force applied kit is easy to operate.

Single pump for shutter movement and cooling water loop.

Parameter：

• Up to 7.5 in x 7.5 in. (19 cm x19 cm) sample size

• Copper slug calorimeter sensors (ASTM or ISO)

• ± 0.75°C temperature measurement

• ± 3% radiant heat flux measurement

• Device Dimensions: 42 in. x 20 in. x 18 in. (107 cm x 51 cm x 46 cm)

• Space Requirements: 46 in. x 26 in. x 24 in. (117 cm x 67 cm x 61cm)

• Power Requirements: 208-265 VAC, 50/60Hz, Single-phase

• Maximum nominal current 20 Amps

• Compressed Air: Clean/dry air at 70-90 PSI, (145 PSI max)

• Cooling Water: Cooling water required, chiller or tap water source is acceptable

• Propane Requirement: Regulated supply at 15 PSI (minimum)

• Water-cooled radiant heat source with 9 quartz (500W) infrared lamps

• Two gas burners with flame detection auto ignition

• Mass flow controller for precise gas control

• Water-cooled protective shutter

• Pneumatic sample carriage and shutter assembly

• Integrated sensor cooling stand (air cooled)

• Emergency stop cuts gas flow, power to lamps and pneumatics

• Tinted tempered glass shield protects operator

• Software safety interlocks monitor water flow, carriage position, burner ignition

Other supplier products

	Dental material color stability tester	The Dentistry Base Polymer Search Stability tester evaluates color stability of dental base polymers (used in restorations like dentures) under var...
	Xenon lamp aging test chamber	TheXenon lamp aging test chamberis a photoaging tester for large-capacity textile testing. With additional sample light frame, temperature sensor a...
	Single Cable Vertical Flame Tester	Single Cable Vertical Flame Tester is used for the vertical flame propagation of a single insulated wire or cable is a bench scale test to determin...
	Dry and Wet Retroreflectometer	The Dry and Wet Retroreflectometer, also known as the Dry and Wet Sand Abrasive Wear Testing Machine, is designed to evaluate the wear resistance o...
	Adjustable Angle Shoes Flexing Tester	The finished shoes will be installed on the finished shoes flexing tester, and the flexed part of the finished shoes will be driven by the finished...

供应产品

Same products

	Blanket Flammability Test Machine	卖方: Standard Groups	Bed Blanket Flammability Tester-It is mainly used for testing the flame retardant performance of ...
	High Temperature Oxygen Index Tester	卖方: Standard Groups	The High-Temperature Oxygen Index (TOI) measuring instrument determines oxygen index at up to 125...
	Limiting Oxygen Index Tester	卖方: Standard Groups	The Limiting Oxygen Index Tester measures the minimum oxygen concentration needed to sustain comb...
	Vertical Flammability Tester	卖方: Standard Groups	Vertical Flammability Chamber for measuring the vertical flame spread for children’ sleepwe...
	45 Degree Flammability Tester	卖方: Standard Groups	Application 45 Degree Flammability Tester is used to determine the burning characteristics of te...