Block-on-Ring Test Machine
You can use theBlock-on-Ring Test Machinefor the following applications and test specimens:
Friction and wear performance testing of lubricating oils and greases
Wear resistance evaluation of coatings under dry or lubricated conditions
Tribological analysis of polymers, ceramics, and composite materials
Friction and wear testing under high-temperature and low-temperature environments
Simulation of industrial material contact conditions with line contact geometry
Standardized performance evaluation of engineering materials
Research and development testing for automotive components
Quality control testing in mechanical, aerospace, and lubricant development laboratories
Standards
The system is suitable for testing in accordance with the following international standards and methods:
(1) ASTM D2509 — Standard Test Method for Measurement of Load-Carrying Capacity of Lubricating Grease
(2) ASTM D2714 — Standard Guide for Calibration and Operation of Ring-on-Block Wear Test Machines
(3) ASTM D2782 — Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Fluids
(4) ASTM D2981 — Standard Test Method for Evaluation of Solid Lubricant Films under Oscillating Motion
(5) ASTM D3704 — Standard Test Method for Wear Characteristics of Lubricating Grease under Oscillating Motion
(6) ASTM G77 — Standard Test Method for Ranking Resistance of Materials to Sliding Wear Using Ring-on-Block Geometry
(7) ASTM G137 — Standard Test Method for Ranking Resistance of Polymeric Materials to Sliding Wear Using Ring-on-Block Geometry
(8) Proposed STM — Wear Testing of Dry Film Solid Lubricants under Unidirectional Motion
Parameters
| Item | Technical Parameters |
|---|---|
| Speed range | Standard: 60–3,600 RPM; Optional: 0.5–7,200 RPM |
| Linear speed | Automatically calculated from shaft speed; programmable RPM setpoints, ramp rates, cycles, and test sequences |
| Load range | Dual-zone pneumatic loading: Low load 10–100 lbs; High load 50–1,300 lbs |
| Temperature range | Standard chamber: Ambient to 200 °C; Optional pressure chamber: Ambient to 250 °C; External chiller for sub-ambient testing |
| Friction force measurement | Electronic load cell, standard range 0–250 lbs; optional low-load range 0–25 lbs |
| Motion modes | Unidirectional rotation or oscillating motion (5°–720°) |
| Test control mode | Time-based, cycle-based, or limit-based automatic shutdown |
| Power supply | 220 VAC, single phase, 50/60 Hz |
| Compressed air | 80 psig, clean and dry |
| Benchtop dimensions | 1,829 × 610 × 762 mm |
| Machine weight | 163 kg |
| Shipping dimensions | 1,220 × 1,016 × 1,067 mm |
| Shipping weight | 246 kg |
在线联系供应商
Other supplier products
 |
Fiber Thermal Shrinkage Tester | The Fiber Thermal Shrinkage Tester is a digital instrument designed for evaluating the dry thermal shrinkage of staple chemical fibers. By using im... |
 |
Aerosol Sensor Test System | Application (1) PM Sensor Calibration and Quality Assurance: For production-line calibration and quality control of PM sensors. (2) PMx and PNx S... |
 |
Safety hat flame retardant performance tester | Product Introduction: Safety hat flame retardant performance tester for safety hat flame retardant performance test, high degree of automation, ea... |
 |
Xenon Arc Weatherometer - lab instrument | The xenon arc lamp, which is capable of simulating the whole natural sunlight spectrum in the most consistent manner, can reproduce the destructive... |
 |
Single Burning Item | Single burning instrument (SBI) was measured supplies (excluding floorings) performance at a single burning heat invasion conditions. Samples were ... |
Same products
 |
Automotive seat durability and strength testing machine | 卖方: Standard International Group (HK) Limited | The Automotive Seat Three-Station Headrest and Backrest Static Strength Testing Machine is design... |
 |
Racing Seatback Headrest Restraint Device, Front and Rear Impact Testing Machine | 卖方: Standard International Group (HK) Limited | The Racing Seat Headrest Restraint and Front-Rear Impact Testing Machine is designed to evaluate ... |
 |
Laboratory car wash simulator for automotive testing | 卖方: Standard International Group (HK) Limited | The Laboratory Car Wash Simulator is a specialized testing system designed to replicate automatic... |
 |
Steam jet durability testing machine | 卖方: Standard International Group (HK) Limited | The Steam Jet Test Chamber is designed to evaluate the durability and performance of materials an... |
 |
Seat Bumping and Creep Test Bench | 卖方: Standard International Group (HK) Limited | Application Applications of the Single Station Jounce Tester include, but are not limited to, th... |
