Multi-function drum and reciprocating tribology tester factory
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Application
This testing machine is suitable for friction and wear evaluation under both linear sliding and rotational contact conditions, including:
Reciprocating sliding friction and wear testing of flat samples
Drum rotation wear testing under simulated real-use conditions
Friction testing of photosensitive drums and paper-feeding rollers by rotating them as in actual equipment
Linear reciprocating sliding tests of paper and paperboard samples
Wear behavior evaluation of coatings, polymers, and functional surfaces
Typical test samples include:
Photosensitive drums and transport rollers
Paper, paperboard, and sheet materials
Coated plates and flat specimens
Functional rollers used in printing and conveying systems
Standards
ASTM G133 (Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear)
ISO 7148 (Plain Bearings — Testing of Friction and Wear)
JIS K 7218 (Testing Methods for Plastic Tribological Properties)
JIS P 8139 (Determination of Friction and Wear Properties of Paper and Board)
Parameters
| Parameter | Specification |
|---|---|
| Table size | W 110 mm × L 400 mm |
| Stage travel speed / distance | 30–6000 mm/min / 1–100 mm |
| Operating modes | Single mode, repeat mode |
| Automatic reciprocation count | Max. 9.999.999 cycles |
| Y-axis positioning stage | ±10 mm (reciprocating mode) |
| Drum / roller diameter | Ø10–90 mm |
| Drum fixing method | Dedicated clamping fixtures (customizable by shape) |
| Drum rotation direction / speed | Forward & reverse / 50–500 rpm (custom speeds available) |
| Drum rotation counter | Accumulated up to 9.999.999 cycles |
| Timed automatic stop function | Available, up to 9.999.999 cycles |
| Friction measurement | X, Y, Z directions (Z for vertical load monitoring) |
| Measurement range | Max. 9.8 N for all three directions |
| Vertical load | 1–1000 g (balance arm + weights) |
| 0–10 mm load sensor pressing method (max. 9.8 N) | |
| Pivot vertical movement | 0–150 mm |
| Strain amplifier output | 0–9.8 N = 0–5 V DC analog output |
| Limiter function | Automatic stop at preset friction force in reciprocating mode |
| Measurement position: longitudinal center of sample (drum mode only) | |
| Data analysis (optional) | General friction analysis software for X, Y, Z channels |
Features
Dual-purpose design enables both reciprocating sliding tests and drum rotation tests in a single system
Two loading methods available: traditional weight loading and load-sensor pressing method for drum testing
Real-time monitoring of fluctuating pressing loads during rotation tests
Smooth transition between drum mode and reciprocating sliding mode
Automatic stop function based on preset cycle count or friction force simplifies wear testing
Multi-axis friction measurement provides comprehensive tribological data
Test Procedures
Select the test mode: reciprocating sliding or drum rotation.
Install the appropriate fixture and securely mount the specimen.
Set the required vertical load using weights or load sensor.
Adjust the travel distance, speed, and cycle count or rotation speed.
Configure automatic stop conditions if required.
Start the test and monitor friction forces in X, Y, and Z directions.
Record and analyze friction and wear data during or after testing.
Maintenance Information
Clean fixtures, drums, and contact components after each test
Periodically inspect moving stages, bearings, and balance arms
Verify load accuracy and sensor performance regularly
Keep the instrument in a clean, dry environment
Calibrate measurement channels according to laboratory schedules
在线联系供应商
Other supplier products
 |
Automatic Kinematic Viscosity Tester for Petroleum Products | Whats/App: +86 156 1874 6768 Web: standard-groups.com Application You can use this instrument in the following scenarios: (1) Testing petroleum... |
 |
Impact strength tester for car seat headrest | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Automobile Headrest Strength Tester is designed to evaluate the ultimate strength and d... |
 |
Shoe heat insulation testing machine -- sand bath | Standard GB/T 20991: Determines thermal insulation of safety shoe soles under simulated hot surface exposure. EN ISO 20344: European standard for... |
 |
Direcct flame impingement Tester | Introduction The testerisdesignedaccording to the BS476-12:1991.Method of test for ignitability of products by direct flame impingement.The accu... |
 |
Drill Flocking Performance Tester丨Drill Flocking Performance Test mechine | Standards GB/T 12705.1/14272. BS EN 12132-1 Applications To determine the ability of penetrating to fabric for the liner material, feather or fi... |
Same products
 |
High speed reciprocating friction wear tester | 卖方: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications You can use this tester for... |
 |
Custom fully automatic falling sand abrasion tester | 卖方: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications You can use this tester to ... |
 |
Measuring devices for nanoindentation | 卖方: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications Measuring hardness and elas... |
 |
Multi function Vacuum Tribometer | 卖方: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com Application This tester is designed for ... |
 |
Custom low-load wear testing instrument | 卖方: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com Application The Low-Load Wear Testing Ma... |
