PLC liquid crystal touch impact testing machine (simple suspension)
Get a quote：
Whats/App: +86 181 0160 0864
Web: gellowen.co.uk
A PLC LCD Touch Impact Testing Machine (Simple Suspension) is a type of pendulum impact tester designed to measure the impact resistance of materials using a simple (pendulum) suspension system, with modern control via a PLC (Programmable Logic Controller) and an LCD touchscreen interface.
Product Introduction
Liquid crystal touch impact testing machine is mainly used for hard plastics (including sheet, pipe, plastic profile)， reinforced nylon, glass fiber reinforced plastic, ceramic, cast stone, electrical insulation materials and other non-metallic materials impact toughness measurement, widely used in the chemical industry, scientific research units, universities and other quality testing departments.
Standards
(1)GB/T 11022-2020. GB/T 3906-2020. JB/T 10840-2008.GB/T 7251.1-2013 ，GB/T 7251.4-2017.GB/T 7251.5-2017 ，GB/T 20641-2014
(2)GB/T 20138-2006 ，GB/T2423.55-2006 ，Q/GDW11008-2013
Main features
Not poor quality: the use of high hardness and high-precision bearings, and the use of shaftless photoelectric sensors, fundamentally eliminate the loss caused by friction, to ensure that the friction energy loss is far less than the standard requirements.
Intelligent prompt: According to the impact of the situation, intelligent prompt working status, always interact with the experimenter, to ensure the success rate of the test.
Friendly interface: there are parameter setting interface - result query interface - measurement interface - system setting interface, each operation has a clear user prompt, you can record 10 test records, you can choose domestic and international standards, you can choose Chinese and English.
Accurate measurement: In full accordance with the provisions of the new standard, after 10 swing cycles for a calculation of energy loss, each measurement to go through 3 times to average, to ensure the accuracy of energy loss.
Performance parameters
1. Simple beam impact testing machine
- Impact speed: 2.9m/s
- Impact energy: 1/2/4/5J
- Maximum friction loss energy: <0.5%
- Pendulum prelift Angle: 150±1°
- Strike center distance: 230mm
- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)
2. Cantilever beam impact testing machine
- Impact speed: 3.5m/s
- Impact energy: 1J; 2.75 J; 5.5 J; 11J; 22J(3 hammers, customer's choice)
- Maximum friction loss energy: <0.5%
- Pendulum prelift Angle: 150±1°
- Strike center distance: 335mm
- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)
Accessories
(1)Pendulum (Impact Hammer)
Available in different energy levels for various testing requirements.
(2)Charpy Specimen Support (Anvils)
Used to support specimens during Charpy impact testing.
(3)Izod Clamping Fixture
For vertically clamping specimens in Izod impact tests.
(4)Specimen Alignment Device
Ensures accurate positioning of specimens before impact.
(5)Safety Protection Cover
Prevents debris from splashing during testing and ensures operator safety.
(6)Encoder / Angle Measurement System
Used to measure pendulum angle and calculate absorbed energy.
在线联系供应商
Other supplier products
 |
OSU Rate of Heat Release Apparatus | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk The OSU Rate of Heat Release Apparatus is a precision instrument designed to measu... |
 |
Dynamic footwear water penetration tester / SATRA TM 230 | Application: Dynamic Footwear Water Resistance Tester is designed to determine the dynamic water resistance of all types of shoes. Principle： Th... |
 |
Shoe Shank Stiffness Tester / Footwear Testing Machine | Standard SATRA TM256: Flexural and torsional stiffness testing for athletic, safety, and casual footwear. SATRA TM194: Dynamic fatigue resistance... |
 |
fabric wet adhesion performance tester | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk The Fabric Wet Adhesion Performance Tester is a precision instrument designed to e... |
 |
Blow-By Test Rig | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk Test system for the characterisation of the oil content in blow-by gases at engine... |
Same products
 |
HDPE高速水冷双壁波纹管生产线 | 卖方: Shandong HUASU Plastic Technology Co.,Ltd. | 机头模具采用双流道结构、氮化磨光处理机头，偏壁调整方便快捷，保证内外层壁厚均匀和稳定成型。 最新设计密闭压力水冷冷却结构，冷却充分，多点分布真空系统，效率更高，生产速度更快。 双层在线扩口功... |
 |
PanEVAP & MVR system | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat... |
 |
PanGAP wide gap welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel... |
 |
PanBloc welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac... |
 |
PanBox welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated... |
