HDPE Butt fusion machine
HDPE BUTT FUSION MACHINES
Butt fusion is a thermofusion process which involves the simultaneous heating of the ends of two pipe/fitting components which are to be joined, until a molten state is attained on each contact surface. The two surfaces are then brought together under controlled pressure for a specific cooling time and a homogenous fusion joint is formed. The resultant joint is fully resistant to end loads and has comparable performance under pressure to the pipe itself.
An electrical heater plate is used to raise the temperature of the pipe ends to the required fusion temperature. Butt-fusion can be used to join both PE80 and PE100 materials for the pipe sizes of 90mm and above of the same SDR.
The butt welding machines used to weld PE pipes have controls to ensure the welding parameters are strictly adhered to. The following parameters are controlled:
- heater plate temperature
- ovality and alignment
- interface pressure
- bead width
- heat soak time
- changeover time
Control of these is necessary to ensure premature failure of the weld does not occur. The field conditions under which PE pipe is welded have a considerable effect on the strength of the joint. In order to achieve an acceptable weld three elements are essential:
- Cleanliness: because contamination will ruin joints
- Technique: Most owners of PE pipe systems require that people performing butt welding of PE pipes are qualified by completing a recognized training course.
- Correctly designed equipment with proper maintenance: Correct welding temperatures, welding procedures and pipe facing tools must be maintained in tolerance and in good condition.
The resulting joint, if it has been properly made, is as strong as the original pipe and can withstand all the loads applied during routine installation and operation.
During the fusion process internal and external ‘weld beads’ are formed. Techniques have been developed to minimize the size of the beads, however as they do not add anything to the overall strength they may be safely removed if required. The removed weld beads can be inspected as part of a quality control programme.
在线联系供应商
Other supplier products
 |
SWT-NSGM2 Hdpe Geomembrane With Hot Wedge | SWT-NSGM2 Geomembrane welderis of membrane laying way towards one edge, which is usually for welding the sideway membrane and cover membrane of lad... |
 |
SWT-NS900 Hdpe Geomembrane Welding Machine Hot Wedge Welder | Application SWT-NS900 Hdpe Geomembrane Welding Machine Hot Wedge Welder Brief Introduction Geomembrane welder is a new welding m... |
 |
pe hydraulic butt fusion welding machine | SWT-V800/500HC Butt Fusion Welding Equipment Application Suitable for butt welding of plastic pipes and fittings made of PE,PP, and PVDF in worksit... |
 |
SWT-NS2000 1600W High Temperature Resistant Hot Air Gun Plastic Welder | Application SWT-NS2000 1600W High Temperature Resistant Hot Air Gun Plastic Welder Brief Introduction 1. Double insulated , sa... |
 |
HDPE Pipe Thermofusion Welding Machine | PlasticpipesbuttfusionmachineSKC-B630/315H Application SuitableforbuttweldingofplasticpipesandfittingsmadeofPE,PP,andPVDFinworksiteorworkshop. Fea... |
Same products
 |
安泰信 ST-2065D ST-2080D ST-2150D 数字电烙铁 | 卖方: 深圳市维客修科技有限公司 | 描述 ATTEN ST-2065D ST-2080D ST-2150D 便携式电烙铁带LED数字显示，65W 80W 150W可选，80℃-480℃可调温度，适用于手机PCB、... |
 |
Mechanic RS5 多功能焊接台烙铁架 | 卖方: PHONEFIX technology Co.,Ltd | 描述Mechanic RS5 多功能焊接工作台，配有焊锡丝收纳架、烙铁头收纳区、烙铁头拆卸架、焊接手柄睡眠架、烙铁头清洁海绵等。MECHANIC RS5 全铝合金焊接工作站与焊台配合使用，用于手... |
 |
YIHUA 982-III C210 C115 Soldering Iron Station Two-hand Clamp | 卖方: Phonefix | YIHUA 982-III portable precision soldering station with 2 help hands clamp, compatible with T115 ... |
 |
XZZ M1 Pro/M1 Max Reballing Platform For MacBook CPU Repair | 卖方: Phonefix | XZZ M1 MAX and M1 PRO Notebook reballing platform with stencil for MacBook CPU soldering repair. ... |
 |
Original QUICK TS11 90W Smart Precision Soldering Station | 卖方: Phonefix | QUICK TS11 smart precision soldering station with HD color screen for mobile phone motherboard IC... |
