Tobee® 250TV-SP Vertical Slurry Pump
Tobee® 250TV-SP Vertical Slurry Pumpis no submerged bearings or seals heavy duty cantilevered pumps, which ideal for a variety of submerged suction pumping applications. These pumps operate well in a variety of sump conditions, and can also be readily applied on floating dewatering or other floating pump platforms.
Design Features:
• Bearing Assembly - The bearings, shaft and housing are generously proportioned to avoid problems associated with the operation of cantilevered shafts in the first critical speed zones.
The assembly is grease lubricated and sealed by labyrinths; the upper is grease purged and the lower protected by a special flinger. The upper or drive end bearing is a parallel roller type whilst the lower bearing is a double taper roller with preset end float. This high performance bearing arrangement and robust shaft eliminates the need for a lower submerged bearing.
• Column Assembly - Completely fabricated from mild steel. The SPR model is elastomer covered.
• Casing - Has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the SPR.
• Impeller - Double suction impellers (top and bottom entry) induce low axial bearing loads and have heavy deep vanes for maximum wear resistance and for handling large solids. Wear resistant alloys, polyurethane and moulded elastomer impellers are interchangeable. The impeller is adjusted axially within the casting during assembly by external shims under the bearing housing feet. No further adjustment is necessary.
• Upper Strainer - Drop-in metal mesh, snap-on elastomer or polyurethane for TP and SPR pumps. Strainers fit in column openings.
• Lower Strainer - Bolted metal or polyurethane for SP, moulded snap-on elastomer for SPR.
• Discharge Pipe - Metal for SP, elastomer covered for SPR. All wetted metal parts are completely rust protected.
• Submerged Bearings - None
HEBEI TOBEE PUMP CO.,LIMITED
Email:
| |
在线联系供应商
Other supplier products
| Tobee® G8110A05A Volute Liner for 10x8ST-AH Slurry Pump | Tobee® G8110A05A Volute Lineris one of wearing parts for 10x8 AH Slurry Pump, 10x8ST-AH Pump and 10x8F-AH Pump. Slurry Pump Volute Linersare i... | |
| Tobee® S06210E62 Labyrinth for 12x10, 14x12 AH Slurry Pump | Tobee® S06210E62 Slurry Pump Labyrinthis a component of drive end parts can be suit for 12x10 and14x12 AH Slurry Pump, Tobee®can offer vari... | |
| Tobee® Slurry Pump Wetted Parts Impeller B15127NA for 2x1.5B-AH Slurry Pump | Tobee®Slurry Pump Impeller B15127NAis one of the most important parts of 2x1.5B-AH Centrifugal Slurry Pumps. And it is open type with 5 vanes. ... | |
| Tobee® FGD Gypsum Slurry Pump | Tobee®DT Series FGD Gypsum Slurry Pumpis a single stage, single suction horizontal centrifugal pump. Mainly used as the circulating pump for ab... | |
| Tobee® AHR Rubber Slurry Pump | Tobee®AHR rubber lined slurry pumpsare similar to AH metal lined slurry pump instructure. The main difference between AH and AHR is the materia... |
Same products
| WN(Q) Dredging Pump | 卖方: Shijiazhuang Chongmu Fluid Machine Co., Ltd | The dredging pumpis a kind of mud pump developed by our company, which is used for dredging and h... | |
| IH Stainless Steel Centrifugal Pump | 卖方: Shijiazhuang Chongmu Fluid Machine Co., Ltd | The IH type single-stage single-suction cantilever chemical centrifugal pump is an energy-saving ... | |
| Horizontal Multistage Pump | 卖方: Shijiazhuang Chongmu Fluid Machine Co., Ltd | Looking for a reliable horizontal multistage pump manufacturerwith high-quality, durable, and exp... | |
| Diaphragm Pump DP03BL Series | 卖方: PJM MECHANICAL CO.LTD | Diaphragm Pump DP03BL Series We specifically manufacture DP03BL diaphragm pump for use in medica... | |
| Gr300 Pneumatic Conveying Equipment/Air Vacuum Powder Automatic Conveying Equipment | 卖方: Greentech International (Zhangqiu) Co., Ltd | Cast Iron Blow Through Airlock Valve Positive Rotary FeederRotary airlocks displace bulk solids f... |
















