.

SMC Antenna Reflector Mould

Mainly for pressure molding, the cavity pressure should be considered as small as possible when designing the parting surface. The exhaust should be smooth, the position of the discharge, the shape, and the flow of the material should be fully considered, especially for some small ribs. For the movable exhaust, there must be a overflow trough. Vacuuming structure, the mold temperature balance is consistent. The appearance and strength of the product are guaranteed.

There are some features of antennaSMC:

(1) High precision, high efficiency, and high gain.

The most important job of using SMC for the manufacture of antennas is to fully exploit its features and achieve high precision in antenna design from product design and process. Under the condition that the shrinkage ratio of the material and the SMC molding shrinkage rate have been considered in the mold size design, the SMC antenna reflective surface has a smaller shape from the original design paraboloid after molding. That is, the accuracy of the SMC molded antenna is completely guaranteed by the accuracy of the mold. The rms value of the SMC antenna molded integral reflection surface is 0.25 mm, and the rms value of the single-piece reflection surface of the split antenna is less than 0.3 mm, and the rms value of the reflective surface after assembly is less than 0.6 mm.

(2) Corrosion resistance

Conventional antenna materials such as aluminum plates and steel plates are made of metal materials, not as good as SMC which as a non-metal dielectric composite material in terms of acid resistance, alkali, salt, and corrosion resistance. The Pikington laboratory in the United States used infrared to analyze the surface of SMC materials and found that its surface is covered by additives, resin, and very fine calcium acid filler. It has good acid resistance, water resistance and corrosion resistance. The antenna reflection made by this material is solved the disadvantage of the traditional metal material antenna is easy to corrode. In coastal areas, rainy, humid areas and areas with excessive acid rain, the anti-corrosion advantages of SMC molded antennas are particularly prominent. The SMC molded antenna samples were placed in 130 highly corrosive chemical environments at an ambient temperature of 50 ° C. The results showed that the test samples showed little or no change.

(3) long life

The average aluminum plate antenna is as small as 2-3 years in the coastal area, and more often 4-6 years, and it will generally be damaged by salt spray erosion and aging. The most obvious example is the cable TV (CATV) in Taiwan, which was built earlier than the mainland. It is estimated that there are nearly 1000 satellite TV receiving antennas on the island, all built in the mid-1980s, all of which were aluminum plate antennas, until the early 1990s. , that is, has begun to replace. The service life of SMC molded antennas is generally more than 15 years; PROMLIN's prototype SMC molded antennas in 1985 are still working normally, and they are subject to typhoons and heavy rain every year.

(4) Strong wind resistance

Since the antenna reflection surface is designed during the molding process, multiple longitudinal and circumferential rib structures are designed. According to the structural strength calculation, the SMC antenna can withstand a wind load of 45 m/s, which shows its remarkable structural rigidity and strength.

(5) Special reflective layer technology

The reflective surface of the SMC antenna uses a metal aluminum mesh as a reflective layer of electromagnetic waves. The aluminum mesh in the finished antenna is evenly

embedded under the surface SMC, which can reflect electromagnetic waves and insulate the atmosphere, and plays a good protective role.

(6) Good consistency, no deformation, easy to transport and install

Because SMC antenna adopts membrane pressure technology under high temperature and high pressure. Its material properties and processing technology determine the unparalleled consistency of SMC antennas with other antennas. This not only ensures the accuracy and high gain of the antenna, but also is very easy to install and debug. SMC, commonly known as "glass reinforced plastic", has the characteristics of no deformation, which eliminates the adverse effects of antenna deformation on the satellite receiving system during transportation.

SMC/ BMCCompositeProducts Description:

SMC, BMC thermosetting plastic products are produced by SMC and BMC plastic molding process. What is smc plastic?SMC/BMC is one of thermosetting plastics, and SMC/BMC thermosetting plastics are thermosetting molding compounds made of unsaturated polyester resin as matrix resin. The main components of SMC/BMC thermosetting plastics include resins, thickeners, low shrinkage additives, fillers, internal mold release agents, colorants, stabilizers, and the like. It is first formulated into a resin paste and then used to impregnate or blend with a reinforcing material to form a preformed molding material. According to the preforming process and the shape of the obtained preformed material, it can be divided into SMC thermosetting plastic and BMC thermosetting plastic or DMC integral molding plastic. SMC/BMC thermosetting plastics are easy to form, have low molding shrinkage, high dimensional accuracy and good processing performance.



在线联系供应商

至: ZHEJIANG AOBANG TECHNOLOGY CO.,LTD
Your E-mail:
消息正文:


Send to other suppliers

Other supplier products

BMC/SMC Molded Products
BMC/SMC Molded Products BMCSMCthermosetting plastic products are produced by plastic smcand BMC plastic molding process. Types of BMC/SMC Molded Products BMC/SMC Motor...
BMC/SMC Motor
BMC/SMC Motor BMC/SMC Electric MotorsDescription Motor BMCreplaces traditional iron and aluminum, reduces the process, seals more, and has higher safety facto...
BMC, SMC, GRP, GFK Wall Panel
BMC, SMC, GRP, GFK Wall Panel Aobang composite Wall Panel is divided into: BMC Wall seat, SMC Wall Panel, GRP Wall Panel, GFK Wall Panel. Composite Wall Panel the main function...
BMC, SMC, GRP, GFK Ceiling
BMC, SMC, GRP, GFK Ceiling grp ceiling smc ceiling gfk plastic BMC, SMC, GFK, GRPCeiling Ceiling is a kind of decoration on the top of living environment. In short, it ...
Auto Parts Mould
Auto Parts Mould Auto Parts Mould Features Injection molding and pressure molding are the main methods. When designing the flow channel and parting surface, the...
供应产品

Same products

Car Mat Aluminium Vacuum Mould
Car Mat Aluminium Vacuum Mould 卖方: Hebei Shuiyuan Trading Co., Ltd Product Description Vacuum molding is the most popular technology for shaping plastic raw mate...
Auto Mould-Safe and Convenient Operation
Auto Mould-Safe and Convenient Operation 卖方: Taizhou Wanda Plastic Mould Co.,Ltd. Product Name Auto Parts Mould Brand Wanda Mould Model No specific Model Material S136/H1...
SMC Cable Braket
SMC Cable Braket 卖方: ZHEJIANG AOBANG TECHNOLOGY CO.,LTD The SMC cablebracket is a combination consisting of a cable bracket, a post and a fixed pin. The ...
SMC/BMC Antenna Reflector
SMC/BMC Antenna Reflector 卖方: ZHEJIANG AOBANG TECHNOLOGY CO.,LTD (1) High precision, high efficiency, and high gain. The most important job of using SMC/BMC for ...
BMC/SMC Insulation
BMC/SMC Insulation 卖方: ZHEJIANG AOBANG TECHNOLOGY CO.,LTD High-strength, wear-resistant, fire-resistant, color BMC material for medium and low voltage insu...