Flammability Tester for Automotive Wires
Applicable Standards:
Requirements of QC/T703 - 2005, SAE - J 1128 - 2005, DIN 72551, ISO6722 and other standards
Main Parameters:
1) The test chamber is enclosed, with dimensions of 650X450X900mm. The material is stainless steel, and it has a matte black background. 2) High - purity propylene gas or liquefied petroleum gas is used as the combustion gas. 3) The length of the wire or cable under test is 600mm (24in), and the clamping angle of the sample is 45 degrees. 4) The Bunsen burner has a nominal diameter of 9mm. The outer flame of the spray tube is 100mm (4in), the inner flame is 50mm (1/2in), and the temperature of the inner flame is at least 900±50 degrees. 5) The Bunsen burner is placed below the sample and perpendicular to the axis of the sample. 6) Automatic ignition, and the combustion time is 15S. 7) Equipped with a high - precision Type K thermocouple for temperature measurement and an imported TES - 1310 thermometer. 8) Equipped with an exhaust system, and the exhaust gas is discharged by an exhaust fan after the test. 9) JIS3005 horizontal combustion test fixtures and horizontal combustion burners are added. 10) The JIS3005 horizontal combustion chamber: 305x355x610mm 11) Horizontal combustion sample: 300mm; Sample placement angle: horizontal 12) Combustion time: 30S 13) Inner diameter of the Bunsen burner: 10mm, inner flame is approximately 35mm, outer flame: 130mm 14) Shutdown mode: When the preset data is reached
在线联系供应商
Other supplier products
 |
Carbide wear tester | Applicable standards: GB/T 34501-2017: This standard specifies the wear resistance test method of cemented carbide, which is suitable for testing ... |
 |
Air - tightness Testing Device for Automotive Connectors | The air - tightness testing device for automotive connectors uses the pressure principle to conduct non - destructive tightness tests on containers... |
 |
Automobile Wire Cross-linking Test Device | Applicable Standards: SAE J1128 - 2005 and other standards Main Parameters: 1. Test rod: Φ6mm, 300mm in length 2. Hot plate specification: ... |
 |
GMA Ultra-filtration Membrane Porometers | TRANSLATE with x English Arabic Hebrew Polish Bulgarian Hindi Portuguese Catalan Hmong Daw Romanian ... |
 |
Button Impact Tester | Button Impact Tester Testing Standards:ASTM D5171 Applications:Button Impact Tester is used to determine the impact resistance of plastic sew-thr... |
Same products
 |
Air Permeability Tester STD- F8 | 卖方: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | 卖方: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | 卖方: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | 卖方: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | 卖方: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
