Respiratory Resistance Tester

Respiratory Resistance Tester Introduction:

The respiratory resistance tester is used to determine the inspiratory and expiratory resistance of respirator and mask protective equipment under specified conditions. It applies to do the relevant detection and inspection for the national labor protection equipment inspection agencies, masks manufacturers of ordinary masks, dust masks, medical masks, and anti-haze masks products.

Standards:


GB 19083,
GB 2626,
GB/T 32610,
42 CFR Part 84
JIS/T 8151
EN 149,
EN 12941,
EN 14594,
NFPA 1972


Respirator Breathing Resistance Tester Technical Parameters:

1. The instrument consists of an air source that can adjust the flow rate, a human head mold specified in the standard, two intubation systems for inhalation and exhalation, and a respiratory resistance measurement system.
2. The flow sensor has high sensitivity and has a very small starting flow.
3. The flow sensor chip uses a thermal mass flow meter, which does not require temperature and pressure compensation, ensuring high-precision measurement of the sensor. The range of the flow meter is 0 L / min ~ 100L / min, and the accuracy is ± 2%.
4. Multiple sensors are integrated on a single flow sensor chip, which greatly improves the range ratio of the sensor.
5. The zero point stability of the flow sensor is high, with full range and high stability, high accuracy with full range and excellent repeatability, low power consumption, low pressure loss and fast response speed.
6. The data logger adopts a graphic dot matrix LCD with a resolution of 128 × 64 and a full Chinese interface, which is easy to operate.
7. There is 4M memory in the data logger for measurement value recording.
8. The micromanometer sensor uses a two-wire system, with high accuracy and good stability; it is safe and reliable to use an explosion-proof design.
9. The range and zero point of the micromanometer sensor are continuously adjustable, the damping is adjustable, there is no mechanical moving part, and the maintenance workload is small. The micro-pressure measurement range is -1000Pa to 1000Pa, and the accuracy is 1Pa.
10. The whole instrument adopts special gas path conversion elements, which ensures the convenient and fast conversion of the two-pipe system of exhalation and inhalation.
11.The suction volume of the suction pump is not less than 40L / min ~ 100L / min
12. Ventilation volume is constant at (85 ± 1) L / min
13. Power supply: AC220V, 50Hz

Respiratory Resistance Test machine Feature:

▶The instrument consists of gas source that can regulates the flow, standard specifies of small human head mold, inspiratory and expiratory line system, a respiratory resistance measurement system, and so on.
▶Flow sensor has high sensitivity and minimal start flow. Flow
sensor chip uses thermal mass flowmeter, no temperature and
pressure compensation to ensure the sensor's high-precision measurement.
▶ Multiple sensors are integrated on a single flow sensor chip, resulting in the sensor range greatly improved.
▶The zero stability of the flow sensor is high, with full range of high stability, with full range of high accuracy and excellent in repeatability, with low power consumption, low voltage loss and fast response characteristics.
▶ Data recorder uses graphics dot matrix LCD with resolution of 128 × 64, entire Chinese interface, easy to operate.
▶ There are 4M memory in the data recorder for record the measured value.
▶Micro-pressure gauge sensor adopts two-wire system, has high precision, good stability; And adopts anti-explosion design for safe and reliable.
▶ Micro-pressure gauge sensor range, zero external continuously to adjustable, damping adjustable, no mechanical moving parts, less maintenance work.
▶Adopting special air-switching components to ensure that the two sets of inspiratory and expiratory piping system replacement is quick and easy.
▶Digital show the respiratory resistance, with zero calibration, accuracy calibration and over-range alarm function.
▶Equipped with a silent air compressor and air filter to ensure that the test environment is quiet and tidy.
▶Meeting with the latest national standards, compatible with labor and daily protective masks.


Respiratory Breath Resistance Test Machine Maintenance:

1. Do not carry it by the bottom of the control box during transportation to avoid being crushed.
2. Please wipe the electroplated part with oil to prevent rust and keep bright.
3. After the test, please wipe the machine clean, and regularly oil the active fulcrum to increase its service life and sensitivity. (The lubricating oil can be mixed with butter and a little engine oil)
4. Please wipe the panel (control box or display) with a dry cloth to prevent it from getting wet, so as not to damage the IC electronic parts.
5 Please place all fixtures and joint accessories properly, and wipe off the anti-rust oil to prevent rust.
6 After the machine is transported and placed, the foundation and the level must be fixed steadily.
7. Please input power as indicated. (Note that the phase of the input power supply must be correct, otherwise leakage will occur)
8 Ground wire Please perform ground output according to specifications to avoid danger of leakage and signal interference.
9 Do not pull out the plug during work.
10 Please operate and maintain by professional personnel. In case of major problems, please inform our maintenance department to dispatch personnel to handle it. Do not dismantle parts by yourself to avoid causing major losses.

Other supplier products

	Helmet Surface Protrusion Shear and Friction Tester/ helmet surface friction testing machine/ Helmet surface protrusion shear tester	In the realm of protective headgear, a helmet's primary role is to absorb and deflect impact forces to safeguard the wearer's head. However, the ex...
	Paper smoothness meter	Product Information: Implementation standards: ISO 5627 Paper and board - Determination of smoothness （Buick method） GB/T 456 "Paper and board s...
	G651 national standard shoe bending tester	Product Introduction: National standard shoe bending testing machine is specialized in testing finished shoes and soles, after a long time, fixed ...
	Mask Leakage Tester	Mask Leakage Tester - Non-woven and Geomembrane - standard Applications: The Mask Integrity Test Accessory (MITA) works in tandem with the CBRN...
	Safety shoe impact testing machine	Safety shoe impact testing machine - Other test instrument - standard Product Introduction: According to standards BS-953,1870,EN-344,ANSI-Z41,CS...

供应产品

Same products

	PH-2398 pH/EC/ORP/温度 多参数测试仪	卖方: 科立龙电子股份有限公司	大显示，可同时进行水质PH、氧化还原电位、电导率、温度的测量； 带背光LCD显示清晰，功能齐全，精度高； 仪表采用微电脑测量与控制技术，具有自动校准功能，方便实用。 内置蓝牙，可以与电脑或...
	ORP-2026S 防水型 土壤ORP&温度 二合一测试仪	卖方: 科立龙电子股份有限公司	范围 ORP -999～999mV Temp 0～50℃ 分辨率 ORP 1mV...
	防水型 EC /TDS/温度三合一参数测试仪	卖方: 科立龙电子股份有限公司	范围 EC ～19.9mS TDS Temp 0～50℃ 分辨率 ...
	EC-98330 电导率营养测试棒	卖方: 科立龙电子股份有限公司	本营养测试仪适用于水培和农业应用，能够准确测量水中的营养液电导率（EC）单位为mS/cm，以及总溶解固体（TDS）转换为百万分之一（ppm）。 适合需要较高EC值的植物，该测试仪具有高达6.0...
	PH-808防水笔式土壤PH计	卖方: 科立龙电子股份有限公司	两点按键校准,自动识别pH标准缓冲液 自动温度补偿确保全量程范围的精确测量。 自动电源关闭，有效节省电池能耗。 可替换型电极降低仪表维护与使用成 全防水性能保障在恶劣环境中对仪表的完整保...