Medical injection needle puncture force tester
Medical injection needle puncture force tester - Other test instrument - standard
Product Information:
The needle puncture force simulates the skin tester with a 5.7-inch (120 x 90) single color LCD touch screen, which is displayed in the Chinese menu. Nominal specification, pipe wall, test number, pressure, upward, downward, time, calibration.
The keyboard controls the menu on the LCD screen, and the airborne print test data. Real-time display of puncture force and peak force data can show maximal puncture force and F 5 peak force. The needle puncture force simulates the complete character of the skin tester.
It is designed and manufactured in accordance with the relevant provisions of GB15811 "disposable sterile injection needle".
Principle:
The puncture force of the injection needle was assessed by the maximum peak force measured at the time of the simulated skin using a puncture force test device.
Parameters:
Nominal specification: 0.3 ~ 1.2mm;
Test range: 0.10 ~ 5.00N, accuracy: + 0.01N;
Mobile speed: 100mm/min;
(presented) simulated skin: polyurethane membrane material conforms to GB15811 standard;
Printing method: can print 8, 13 or 20 test data and average puncture force and deviation value each time.
Net weight: 11kg dimensions: 400 x 290 * 240 (mm)
Partial list:
1. Main engine
2. Printing paper 1 roll.
3. A set of clamps.
Weight one set.
5. One-year warranty
6. Operation instructions
7. The instrument is free to upgrade service according to national standards.
Puncture force test procedure:
Will be needle and simulate the skin in the 22 ℃ plus or minus 2 ℃ for at least 24 h, and at the same temperature test;
The suitable size of the simulated skin clamp on the fixture shall not have any obvious stretching or compression force applied to the simulated skin.
The needle is installed on the device, and its axis is perpendicular to the surface of the simulated skin, and the tip points to the center of the circular puncture zone.
Set the moving speed to 100mm/min.
Start the testing device.
In the process of puncture, the maximum sharp value or record force/displacement diagram was measured simultaneously.
在线联系供应商
Other supplier products
 |
Metal Bone Screws Torque Tester | Standard YY/T 1506, ASTM F543: The standard specifies the torque required to measure the torque required to screw a metallic bone grafting screw ... |
 |
Scorch Tester Sublimation fastness tester | In the daily process of shaping and high temperature ironing, dyes heat stability will affect the appearance of fabrics.. Dyes heating , heat trans... |
 |
Medical Mask Differential Pressure Tester YY 0469-2011 YY/T0969-2013 | Standards: YY 0469-2011 YY/T0969-2013 EN 14683:2014 Annex C ASTM F2100 Product Information: Medical Mask Differential Pressure Tester also calle... |
 |
Photovoltaic module backplane peeling strength testing machine | Introduction: The Photovoltaic Module Backplane Peeling Strength Testing Machine is a specialized device designed to evaluate the peeling strength... |
 |
Hexapod Tumbler test machine | Applications: The Hexapod Tumbler Tester is a popular apparatus used in the evaluation of the appearance retention of carpets. Provides a rapid ... |
Same products
 |
Falling Sand Abrasion Test machine | 卖方: Standard International Group (HK) Limited | The sand abrasion tester is a specialized testing device used to evaluate the abrasion resistance... |
 |
Conveyor Belt Drum Friction Testing Machine | 卖方: Standard International Group (HK) Limited | Main Purposes of Conveyor Belt Drum Friction Testing Machine The conveyor belt drum friction tes... |
 |
Dry Sand Rubber Wheel Wear Tester | 卖方: Standard International Group (HK) Limited | The dry sand rubber wheel abrasion tester is mainly used to test the abrasion resistance of mater... |
 |
Sliding Bearing Fatigue Testing Machine | 卖方: Standard International Group (HK) Limited | The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua... |
 |
High temperature vacum friction & wear tester | 卖方: Standard International Group (HK) Limited | The working principle of a high-temperature vacuum friction and wear testing machine is to simula... |
