Respiratory Resistance Tester
Standards:
· GB/T 2626-2006 Respiratory protective equipment -- non-powered air-purifying particle respirator - 6.5 6.6 · GB/T 32610-2016 Mask technical specification of daily
Applications:
The respiratory resistance tester is used to determine the inspiratory and expiratory resistance of respirator and mask protective equipment under specified conditions.
Product Information:
It applies to do the relevant detection and inspection for the national labor protection equipment inspection agencies, masks manufacturers of ordinary masks, dust masks, medical masks, and anti-haze masks products.
Technical Parameters
·Flowmeter range is 0 L / min -100L / min, accuracy is ± 2%;
·Micro-pressure gauge range is 0-1000Pa, accuracy is 1Pa;
·Suction pump pumping capacity is not less than 100L / min;
·The ventilation capacity was constant at (85 ± 1) L / min;
·Power supply: AC220V, 50Hz
Feature
·The instrument consists of gas source that can regulates the flow, standard specifies of small human head mold, inspiratory and expiratory line system, a respiratory resistance measurement system, and so on.
·Flow sensor has high sensitivity and minimal start flow. Flow
sensor chip uses thermal mass flowmeter, no temperature and
pressure compensation to ensure the sensor's high-precision measurement.
·Multiple sensors are integrated on a single flow sensor chip, resulting in the sensor range greatly improved.
·The zero stability of the flow sensor is high, with full range of high stability, with full range of high accuracy and excellent in repeatability, with low power consumption, low voltage loss and fast response characteristics.
·Data recorder uses graphics dot matrix LCD with resolution of 128 × 64, entire Chinese interface, easy to operate.
·There are 4M memory in the data recorder for record the measured value.
·Micro-pressure gauge sensor adopts two-wire system, has high precision, good stability; And adopts anti-explosion design for safe and reliable.
·Micro-pressure gauge sensor range, zero external continuously to adjustable, damping adjustable, no mechanical moving parts, less maintenance work.
·Adopting special air-switching components to ensure that the two sets of inspiratory and expiratory piping system replacement is quick and easy.
·Digital show the respiratory resistance, with zero calibration, accuracy calibration and over-range alarm function.
·Equipped with a silent air compressor and air filter to ensure that the test environment is quiet and tidy.
·Meeting with the latest national standards, compatible with labor and daily protective masks.
在线联系供应商
Other supplier products
 |
Solid electrolyte analysis system | Standard ISO 9001:2015(Quality Management System) ASTM E1970-21(Standard Guide for Electrochemical Impedance Spectroscopy) IEC 62660-2(Secondary... |
 |
Dynamic waterproof bending testing machine for finished shoes | It is used to test the dynamic waterproof performance of various finished shoes, and the number of times when no water enters the finished shoes or... |
 |
AATCC Accelerotor | AATCC Accelerotor - Textile and Apparel - standard Standards: ATCC 93,M&S P26,M&S P53,NEXT 31 Applications: AATCC Accelerotor, to... |
 |
Absorbable Bone - connecting Plates Four - point Bending Tester | Standard ASTM F2119: Standard test method for constant load testing of bioabsorbable screws and washers, applicable to bending performance evalu... |
 |
PV Backsheet Abrasion Tester | Standard IEC 61730-2: Photovoltaic (PV) Module Safety Qualification – Requirements for Testing UL 1703: Flat-Plate Photovoltaic Modules a... |
Same products
 |
Falling Sand Abrasion Test machine | 卖方: Standard International Group (HK) Limited | The sand abrasion tester is a specialized testing device used to evaluate the abrasion resistance... |
 |
Conveyor Belt Drum Friction Testing Machine | 卖方: Standard International Group (HK) Limited | Main Purposes of Conveyor Belt Drum Friction Testing Machine The conveyor belt drum friction tes... |
 |
Dry Sand Rubber Wheel Wear Tester | 卖方: Standard International Group (HK) Limited | The dry sand rubber wheel abrasion tester is mainly used to test the abrasion resistance of mater... |
 |
Sliding Bearing Fatigue Testing Machine | 卖方: Standard International Group (HK) Limited | The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua... |
 |
High temperature vacum friction & wear tester | 卖方: Standard International Group (HK) Limited | The working principle of a high-temperature vacuum friction and wear testing machine is to simula... |
