Wood Hammer Mill Price/Wood Hammer Mill Supplier
As the name suggests, wood hammer mill price/wood hammer mill supplier is the diesel driven crushing machine. It mainly consists of three parts on the whole: feed hopper, grinding cell, winding system. After the raw materials were put into crushing chamber, the high-speed operated hammer sheets will impact the raw materials over and over again, then the raw materials will be crushed into pre-set size step-by-step. Materials grinded by the crusher are widely used for wood pellets, wood briquette, wood composite board production.
It’s commonly used for crushing material at home and farm or in small scale wood processing factories. The raw materials the machine can process are: wood barks, wood cuttings, crop stalks, rice husk, cotton stalks, coconut shells, sunflower husks, wheat straw, rice straw, palm kernel shells, haulm, peanut straw, sweet potato straw and so on. The final products of the hammer mill, fine and uniform, have a wide application for biomass fuel pellets, animal bedding and other wood product production.
Key Features of Wood Hammer Mill Price/Wood Hammer Mill Supplier
1. We can customize the following sieve with screening hole diameter of 1.8mm-10mm.
2. You can change screening sieve according to different material grinding requirements.
3. With a workhorse of 22HP, a diesel engine can accept a large production work on a daily basis.
4. Both coarse and fine grinding can be realized through adjusting the gap between hammers and screen
5. The core part ---the hammers are made of high quality carbon alloy steel, which is durable and wear-resistant.
6. Available screen discharge area can be up to1904 square centimeter which allows for high throughput at a lower horse power.
7. Equipped with air blower, the crushed material can be directly collected and transported to next machine for further processing.
8. The rotor of hammer mill operates at 3,500 RPM to produce high hammer tip speed, thus the finished powder can be uniform with the least size.
Operation Procedures of Wood Hammer Mill Price/Wood Hammer Mill Supplier
1. Before start, operator should read this manual carefully to learn about hammer mill structure, performance and operation method.
2. Then, adjust and maintain hammer mill machine on following manual regulations. At the same time check the tightness of fastening parts and make sure each part is lubricated sufficiently.
3. After securing the safety of hammer mill machine and operator, idle the hammer machine for 2-3 minutes on hearing no abnormal sounds. Then feed the raw material.
4. Feed the material in slow and steady way. Overload feeding is forbidden. During material blocking at the entrance keep hands away from the feeding port.
5. Fit the sieve mesh with the machine lower body tight to avoid material leakage to affect the crushing quality.
6. Stop and then inspect the machine if there is any abnormal noise during operation. It is forbidden to inspect hammer machine on running.
7. Keep frequent inspection on hammer blades worn degree and cotter pin condition, and replace the worn parts in time on cutting off the power source. Opening the upper body during running is forbidden.
8. After each shift, idle the machine for 5-10 minutes to suck the material clean and stop the machine. Add lubricating grease to main shaft bearings.
Contact Infomation
Email:
Website:
Address: High and New Industrial Zone, Kexue Revenue, High and New Technology Industrial Development Zone, Zhengzhou, China
在线联系供应商
Other supplier products
|
|
Wood Hammer Mill Price/Wood Hammer Mill Supplier | As the name suggests, wood hammer mill price/wood hammer mill supplier is the diesel driven crushing machine. It mainly consists of three parts on ... |
 |
Latest Advanced Ring Die Rice Husk Pellet Mill for Sale | Rice husk, the main by-product from rice milling, is the most suitable raw material for pelletizing . Therefore, the rice husk pellet mill has good... |
 |
Hot Selling Wood Pellet Plant/Wood Pellet Plant Supplier | Hot selling wood pellet plant/wood pellet plant supplier adopts advanced technology and design this model of machine on the base of fully understan... |
 |
Reliable Performance Corn Stover Pellet Mill for Hot Sale | Modern technological innovation and design have been combined with the latest creating technological company to provide the best excellent pellet g... |
 |
Cotton Stalk Pellet Mill Price/Cotton Stalk Pellet Machine Supplier | Stalk pelletizing technology is the use of rice straw, wheat straw, corn stalks and other agricultural waste as raw material, through special straw... |
Same products
 |
OEM China Diamond Grinding Shoe Suppliers and Manufacturers | 卖方: Xiamen ChinShine Industry and Trade Corporation | Diamond grinding shoes are essential tools in the construction and flooring industries, offerin... |
 |
Grafting Tool | 卖方: Zhejiang GuYueHu Industry&Trade Co.,Ltd. | All-in-one grafting tools and equipment for sale: professional grafting tool, 3 different blades ... |
 |
Electric Tomato Pollinator | 卖方: Zhejiang GuYueHu Industry&Trade Co.,Ltd. | Electric Tomato Pollinator This electric tomato pollinatoris a very effective tool to increase t... |
 |
高质量木工滑台锯 | 卖方: 青岛联合瑞亚国际贸易有限公司 | UA3200S:3200*375mm.Saw blade:300mm. Scoring saw blade diameter:120mm.Main motor:5.5kw.Scoring mot... |
 |
High quality Sliding table saw For woodworking | 卖方: 青岛联合瑞亚国际贸易有限公司 | UA1600S:1600*375mm. Saw blade:300mm. Scoring saw blade diameter:120mm.Main motor:3kw.Scoring moto... |
