Burning Manikin System

The burning manikin system is used to test the overall thermal protection performance of protective clothing.Complete combustion manikin system, which consists of combustion chamber, burning manikin and gas control system and other components.

Standard:

EN ISO 11612. EN ISO 11611. ISO 13506. EN469:2005.

Principle:

The burning manikin system is composed of:

1. computer combustion dummy;

2. thermal sensor group;

3. flame generator;

4. computer control module;

5. data acquisition and processing module;

6. burn analysis module.

1. The burning manikin model uses 1: 1 adult male model, the material is FRP with stable, flame inert and high strength performance, and 2 ~ 3mm thickness, 1.72m2 surface area. There are a certain number of sensors in the manikin model’s head, trunk, legs and arm surface evenly. The manikin model’s outer surface paints black and flame retardant coating. The processed sensor data export lines on the head facilitate the instrument to capture the data signal.

2. The sensor group includes thermal sensor and pressure sensor. The heat sensor consists of more than 120 heat flow sensors, which are evenly distributed on the manikin's surface, and each sensor represents the physical condition of the skin of a certain surface area. Numbered every sensor, and if the temperature value calculated by the sensor passes burns are estimated to meet the two or three burning degrees, then mark them into a simulated digital human body model with different colors. Since the flame temperature change is a dynamic process, the test sensor temperature range is higher and the response time is shorter to achieve the flame dynamic process of the test. Pressure sensor is mainly used to measure the gas container and gas pipeline gas pressure value, to ensure safe and controllable experimental.

3. The flame generation device consists of 6 groups of 12 propane flame generators around manikin. Each group of flame generators consists of a high pressure liquefied gas tank, a buffer gas tank, a pressure pipe and a gas pressure sensor, a adjustable flame nozzle, and a pilot flame device. Flame action time is controlled by the computer control simulation module, the flame intensity during this period maintains uniform and stable.

4. The computer control module is composed of pre-programmed software. The main function is to automatically check the status of each group of sensors associated with the experiment before the start of the experiment. Send the command when no problem. In the course of the experiment, the computer control program controls the time and intensity of the flame generator, automatically guide the data processing module and record the data changes of the various sensors. In the end of experimental stage, downloaded and saved the recorded data into the form of the document, and guide the exhaust ventilation system on the combustion test chamber for ventilation.

5. Data acquisition and processing simulation. With the help of computer control module, preprocess the signal of the amplification, conversion and storage data for control temperature sensor and heat flow sensor acquisition. the heat flow signal transfer into the corresponding temperature value through the model, and then the results are temporarily stored for the burn estimator module use.

6. The burn estimation module is intended to estimate the extent of burns caused by the flame. The information of the manikin surface temperature value obtained by the sensor is input to the burn estimation model. After the burn estimation operation, the burn integral value and the burn program value are obtained. Combined with the plot of the digital human body model to get the second and third degree burns on the scattergram manikin's surface.

Other supplier products

	Fire retardant coating tester	Product Introduction: The tester conforms to the technical indicators and requirements specified in the national standard GB12441-2005. and is sui...
	Civil Aviation Aircraft Interior Non-metallic Materials Flame Retardant Property Tester	I. Applicability Scope This system applies to combustion performance testing of non-metallic materials in aircraft cabins: 1.1 Crew/Passenger Cab...
	Fireproof coatings tester	Sample making: 1. The test plate of the fireproof coating tester (small chamber method) is made of birch five-layer plywood conforming to GB738-75...
	Building Materials Non-combustibility Tester	Building materials non-combustibility testeris designed to test the combustibility of main components in homogeneous and nonhomogeneous building pr...
	Thermal Radiation Flooring Combustion Tester	Product Standards ISO 9239 - 1: Reaction to fire tests for floor coverings - Part 1: Determination of the burning behaviour of floor coverings usi...

供应产品

Same products

	FH-77富氢测试笔	卖方: 科立龙电子股份有限公司	产品说明： 用于测量氢气水（富氢水）和氢气水发生器的溶解氢含量。 特征： 1、电极更换方便 智能、携带方便、操作方便、实用； 产品广泛应用于食品、环卫、地质勘探、冶金、地表水、 ...
	Xenon Arc Weather Ometer	卖方: Standard Group (Hong Kong) Limited	Get a quote： Whats/App: +86 181 0160 0864 SI4000Xenon Arc Weather Ometer utilizes a xenon lamp ...
	Xenotest | Light Fastness Tester Si220 (SunTest)	卖方: Standard Group (Hong Kong) Limited	Get a quote： Whats/App:+86 180 0160 0864 A Light Fastness Tester, or Xenon Tester, Accelerated ...
	Ozone Aging Chamber	卖方: Standard Group (Hong Kong) Limited	Get a quote： Whats/App:+86 156 1874 6768 The Ozone Aging Chamber is a precision testing instrum...
	Plastic Smoke Density Tester F313	卖方: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com The F313 Plastic Smoke Density Tester is ...