Fire retardant wood burning test equipment
Product Introduction:
Fire retardant wood stack method combustion test device is a test device developed and produced by referring to the People's Republic of China public safety industry standard GA/T42.1 "Fire retardant wood combustion performance test method - Wood stack method". MDF-1 type flame retardant wood wood stack combustion test device is suitable for testing the combustion quality loss rate and flame burning time of all kinds of wood with thickness above 20mm in production and engineering after flame retardant impregnation treatment under specified combustion conditions.
Working conditions:
1. Ambient temperature: room temperature —— 35oC
2. Ambient humidity: ≤70%
3. working voltage: AC 220±10V
4. gas source: natural gas, liquefied petroleum gas
5. timing accuracy: 3min±GA/T 42.1 Flame retardant wood burning performance test method wood stack method 0.1s
6. temperature error: 310oC≤±10oC
Specimen preparation:
1. The specimen size is 76mm×13mm×13mm, the cutting error is ±1mm, and the surface is required to be smooth and flat. Three sets of 24 pieces were prepared for each test piece.
2. The specimen is cut 0.6mm away from the longitudinal end of the wood, less than 1m long wood, and cut from the middle to both sides.
3. the specimen cut from the upper and lower sides of the width of the wood along the thickness direction parallel cut 13mm×13mm test piece two layers, and then cut 76mm along the length direction of the test piece, the remaining center part is not sampled.
4. before the test, the specimen must be at a temperature of 23±2oC, relative humidity (50±5) % of the condition, so that its quality is constant. The determination condition is the interval of 24h, the mass change of two weighing before and after each group is not more than 1%.
在线联系供应商
Other supplier products
 |
Micro-controlled High-temperature Tribological Tester | Applicable Standards When conducting tests, the microcomputer - controlled high - temperature friction testing machine usually needs to comply wit... |
 |
Diaper impurity testing machine | Introduction: The diaper impurity detector is used to detect the impurities remaining inside the diaper under a certain strong light irradiation. ... |
 |
Timken Test Machine | Testing Standards ASTM D 2509 ASTM D 2782 GB/T3142 SH/T0204 Applicable standards Timken extreme pressure friction testing machines are usuall... |
 |
Vacuum Ball - Disk Friction Tester | Main Purposes of Vacuum Ball - Disk Friction Tester The vacuum ball - disk friction tester is a device specifically used for evaluating the slidin... |
 |
Coating abrasion resistance tester | Product Introduction: The determination of scratch resistance of the coating is very similar to the scratch test of the coating, but this test met... |
Same products
 |
FH-77富氢测试笔 | 卖方: 科立龙电子股份有限公司 | 产品说明： 用于测量氢气水（富氢水）和氢气水发生器的溶解氢含量。 特征： 1、电极更换方便 智能、携带方便、操作方便、实用； 产品广泛应用于食品、环卫、地质勘探、冶金、地表水、 ... |
 |
Xenon Arc Weather Ometer | 卖方: Standard Group (Hong Kong) Limited | Get a quote： Whats/App: +86 181 0160 0864 SI4000Xenon Arc Weather Ometer utilizes a xenon lamp ... |
 |
Xenotest | Light Fastness Tester Si220 (SunTest) | 卖方: Standard Group (Hong Kong) Limited | Get a quote： Whats/App:+86 180 0160 0864 A Light Fastness Tester, or Xenon Tester, Accelerated ... |
 |
Ozone Aging Chamber | 卖方: Standard Group (Hong Kong) Limited | Get a quote： Whats/App:+86 156 1874 6768 The Ozone Aging Chamber is a precision testing instrum... |
 |
Plastic Smoke Density Tester F313 | 卖方: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com The F313 Plastic Smoke Density Tester is ... |
