.

24dBm 900 2100 Dual Band Signal Booster MGC AGC ALC

HPC-GW-27A GSM900 and 3G 2100mhz Dual band signal repeatersProduct introductionMobile signal booster is designed to enhance the indoor mobile signal. The main reason leads to the weak indoor signal is the rebar inside of the concrete walls. Because the rebar will absorb and isolate the wireless signals.This product can amplify the wireless signals by special outdoor antenna and signal process circuits. The mobile signals will be transmitted into indoor space again after being magnified. The indoor signal would be enhanced because it will not be absorbed by the rebar concrete.Features:Light weight, compact size and high performance. Provides a quick cost effective solution to indoor coverage problems. Reduces dropped calls. High linear design, low interference to the BTS. Low power consumption, ease of installtion and great coverage. Intelligent design with built in ALC function, ATT manual attenuation control at 1db/steps. With proper installation, expected coverage is 100~1500m². Reduces cell radiation and extends cell battery life.DescriptionHPC-GW-27A  Dual band repeater is to support any two mobile band existing in the world to help end users to improve mobile signals for much better call quality and smoother data transmission. It is designed to support coverage area up to 100-2000 square meters with proper engineering. Below are the main features.1. The consumer repeater is an ideal solution for providing a cost effective improvement in cellular in-building coverage of a home, office, restaurant or building, in the quickest time possible.2. Manual gain control (MGC) available for both uplink and downlink to adjust the gain value for proper coverage during installation or maintenance.3. To maintain safe and specific output signal levels and give alarms on self-oscillation, the repeater has built-in AGC and ALC circuits, which can automatically control the gain of the repeater depending upon the strength of input signals.4. Auto shut off function available for both uplink and downlink to avoid deep self-oscilation from jamming the towers, saving your trouble from operators. 5. Wide band feature enables all devices operating within the wide frequency range of the repeater to see an improvement in performance.6. Multiple s and other handheld devices throughout a building can benefit from a wireless repeater.7. Supports up to (180) users / calls simultaneously.8. Extended battery life. (Your does not need to put out as much power due to improved reception.)Specification:Electrical specificationUplinkDownlinkFrequency RangeGSM900890-915 MHz935-960 MHz3G1920-1980 MHz2110-2170 MHzMax .Gain≥ 75dB≥ 75dBMax .Output Power≥ 27dBm≥ 27dBmBand width (-3dB)Wide BandMGC ( Step Attenuation )≥ 31dB / 1dB stepAutomatic Level Control≥ 15dB, auto shut off after 15dBGain FlatnessGSM & CDMATpy≤ 6dB(P-P); DCS,PCS ≤ 8dB(P-P)WCDMA≤ 2dB/ 3.84MHz,Full Band ≤ 5dB(P-P)Noise Figure≤ 8dBVSWR≤ 2.0Group Delay≤ 1.5μsFrequency stability≤ 0.01ppmSpurious Emission & Output inter-modulationGSM Meet  ETSI TS 151 026 V 6.1.0WCDMA Meet 3GPP TS 25.143 ( V 6.2.0 )CDMA Meet  IS95 & CDMA2000WCDMA SystemSpurious Emission MaskMeet 3GPP TS 25.143 ( V 6.2.0 )Modulation Accuracy≤ 12.5%Peak Code Domain Error≤ -35dB@Spreading Factor 256CDMA SystemRhoρ > 0.980ACPRMeet IS95 & CDMA2000Mechanical  SpecificationsStandardI /O PortN-FemaleImpedance50 ohmOperating Temperature-25ºC~+55ºCEnvironment ConditionsIP40Dimensions250x330x53mmWeight≤ 4.5KgPower SupplyInput AC90~264V,output DC12V / 5ALED  AlarmStandardPower LEDPower IndicatorALC LED 1 (Low frequency Band)Orange @ ALC 1~5dB, Red @ ALC 15dB~20dB,LED off after 5 seconds red colorALC LED 2 (Middle frequency Band)Orange @ ALC 1~5dB, Red @ ALC 15dB~20dB,LED off after 5 seconds red colorALC LED 3 (High frequency Band)Orange @ ALC 1~5dB, Red @ ALC 15dB~20dB,LED off after 5 seconds red colorThe installtion of the RepeaterOutdoor antenna ( for receiving the signal from the BTS ) + Cable ( transfering the received signal) + Repeater ( for amplifying the received signal) + cable( for transfering the amplified signal) + indoor antenna( for shooting the amplified signal), Installation steps Step 1 Start by taking your up to the roof or other location outside to find where the signal is strongest.Step 2 Temporarily mount the Outdoor (outside) antenna in that location. You may need to adjust and move the antenna later.Step 3 Run coaxial cable into the building to a convenient loaction (attic, etc.) where you can also get standard power for the Signal Repeater.Step 4 Place the Signal Repeater in that location and connect the coaxial cable to the Outdoor Side of the Signal Repeater and the Outdoor antenna.Step 5 Mount your Indoor (inside) antenna in a productive location. You may need to adjust or move the antenna later. More notes on Indoor antennas and patterns here.Step 6 Connect coaxial cable between the Indoor antenna and the Signal Repeater output port.Step 7 Power up the system and check for signal inside the building. If needed, tune system by moving and or pointing the Outdoor and Indoor antennas until they get the most signal possible.Step 8 Secure all antennas and cables, securely mount the Signal repeater and clean up the installation.Of course there are still a few more things to consider but in general, this is the basic procedure. For more information, please contact us.Terms and ConditionsCertificateCE/RoHsCountry of OriginChinaPort of DispatchShenzhenProduction Capacity1000pcs/monthDate of DeliveryWithin 3 days after received payment informMOQ10pcsWarranty2yearsPacakge1pcs/box; 5pcs/cartonCountry of OriginChina


在线联系供应商

至: Shenzhen Sai Tong Tian Electronic Technology Co.,LTD
Your E-mail:
消息正文:


Send to other suppliers

Other supplier products

20dBm signal repeater Dual system series are designed for business places indoor coverage solution. Such as the bookstore, the restaurant, the coff...
HPC-GDW-27 GSM900 DCS1800 3G 2100 Tri band signal repeatersA cell signal booster (also known as cellular repeater or amplifier) is a device that b...
Dual Band Mobile Signal Booster/3G GSM DCS LTE Cell Phone Signal Repeater Amplifier
5watts 3G signal booster ST-3G&5W Max coverage 6000sqm What is the booster?Cell signal booster (also named repeater, amplifier) is a product desig...
VGA USB Camera module With 24PCS IR LED and IR CutMain SpecificationsModelTD-USB30W04MT-RL36SensorOV7725Lens Size1/4 inchPixel Size6.0um X 6.0umima...
供应产品

Same products

GP-AP450 5.8GHz 450M Industrial Car Wireless AP
GP-AP450 5.8GHz 450M Industrial Car Wireless AP 卖方: 北京光普森科科技有限公司 GP-AP450 is a high performance, high bandwidth, multi-functional and outdoor industrial dual-freq...
1775M WiFi6 Outdoor Industrial Wireless AP
1775M WiFi6 Outdoor Industrial Wireless AP 卖方: 北京光普森科科技有限公司 GP-AP1800AX-FS户外AP产品是GPSENKE自主研发的基于IEEE802.11ax技术的产品。 GP-AP1800AX-FS支持802.11b/g/n/ac/ax标准,双频最大带宽...
SPD for Network / Data Line Surge Protector
SPD for Network / Data Line Surge Protector 卖方: Shenzhen Techwin Lightning Technologies Co., Ltd Data line protector series are mainly used in TCP/IP communication networks to protect electrical...
WiFi IP Phones   SC-2168-WP
WiFi IP Phones SC-2168-WP 卖方: Suncomm Technology., Ltd. Key Features Wireless working frequency 2.4GHz/ 5.8GHz. HD Voice: HD Codec, HD HD Voice: HD Codec...
IP Desk Phones   SC-2007-PE
IP Desk Phones SC-2007-PE 卖方: Suncomm Technology., Ltd. SC-2007-PE IP Phone with PoE; SC-2007-IP IP Phone with AC Power; 2 SIP, TR-069 SC-2007-PE/ SC-200...