Heated plate drying rate tester with digital display
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Standards
AATCC 201-2013 Fabric Drying Rate: Hot Plate Method
FZ/T 01176-2024 Textiles - Determination of Fabric Drying Rate - Hot Plate Method
Features
1. Incorporates high-precision wind speed sensors, infrared temperature sensors, temperature sensors, precision dripping devices, high-accuracy wind speed control units, and fluid dynamics-optimized air ducts.
2. Integrates with computer software to automatically perform fabric drying time and drying rate tests along with comprehensive data analysis, significantly enhancing operational efficiency and measurement accuracy while minimizing human-induced errors.
3. Test software communicates with the main unit via USB port, displaying and saving data as curves and charts for easy analysis and printing. Wide adjustable ranges for wind speed (0.2–4.5 m/sec) and drip volume (0.05–4.5 ml).
4. The hot plate method not only complies with the AATCC 201 testing standard but is also suitable for knitted fabrics or any quick-drying fabrics (excluding fabrics used in socks).
Parameters
| Item | Specifications |
|---|---|
| Air Chamber | Capable of generating 0.2–3 m/sec airflow |
| Heating Plate | 300mm×300mm±1mm |
| Flexible Heating Sheet | 300mm×300mm±1mm |
| Insulation Soft Board | 300mm×300mm±1mm |
| Heating Plate Temperature | 37±0.5°C (with overheat protection) |
| Air Velocity | 0–2.5 m/s±0.1 m/s |
| Infrared Temperature Sensor | 15–50°C±0.1°C |
| Data Transmission | USB data transmission |
| Test Interface | Curves and charts displayed simultaneously |
| Test Report | Automatically saved, easy to print |
| Power Supply | AC 230V, 50Hz/60Hz |
| Overall Dimensions (L×W×H) | 450×320×170 mm |
| Weight | Approximately 45 kg |
Test Procedures
Preparation:Connect the instrument to the power supply. Ensure airflow, heating plate, and infrared sensors are calibrated.
Sample Placement:Position the fabric sample on the heating plate. Ensure consistent contact and sample alignment.
Parameter Configuration:Set target temperature, airflow velocity, and drip volume via the software interface.
Test Initiation:Start the automated test sequence. The system will apply controlled heat and airflow, recording moisture evaporation and drying rate in real-time.
Data Collection:Curves and charts are generated automatically. Save or export results for analysis or reporting.
Completion:Remove the sample after test completion. Power off the device or prepare for the next measurement.
在线联系供应商
Other supplier products
 |
Lead Terminal Strength Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Application This tester is widely applied in: PV Module Lead Terminal Tensile and Torsion... |
 |
Cosmetic UV protection tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Instrument Purpose: Used to evaluate the protective performance of cosmetics against solar... |
 |
Torsional Fatigue Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard YY/T 0857-2011 (China): Specifies torsional fatigue testing protocols for spinal ... |
 |
Rapid screening Calorimeter | Whats/App: +86 156 1874 6768 Web: standard-groups.com The rapid - screening calorimeter is a professional calorimetric instrument for the quick a... |
 |
VW-1 wire and cable burning tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Product introduction VW-1 wire and cable burning tester is suitable for measuring the resi... |
