Communication Equipment PCB
In order to shorten the signal transmission distance and reduce the signal transmission loss, the 5G communication PCB, gradually move towards high-density wiring, fine wire spacing, the development of small aperture, thin profile and high reliability.
Communication Industry And Communication PCB
Communication Industry And Communication PCB
Communications Industry
Major Equipment
Required Communication Circuit Board
Communication PCB Features
Wi-Fi
Communication base station
Backplane, high-speed multilayer board, high-frequency microwave board, multifunctional metal substrate
Metal base, large size, high multi-layer, high frequency materials and mixed lamination
Transmission network
OTN transmission equipment, microwave transmission equipment
Backplane, high-speed multilayer board, high-frequency microwave board
High-speed material, large size, high multi-layer, high density, back drill, rigid-flex combination, high-frequency material and mixed pressure
data communication
Routers, switches, service/storage equipment
Backplane, high-speed multilayer board
High-speed material, large size, high multi-layer, high density, back drill, rigid-flex pcb
Fixed broadband
OLT, ONU and other fiber-to-the-home equipment
High-speed material, large size, high multi-layer, high density, back drill, rigid-flex PCB
Multilayer board, rigid-flex PCB
Process Difficulty Of High Frequency And High Speed PCB Board
Alignment Accuracy
Accuracy is tightened, and tolerance convergence between layers is required. The board size becomes more demanding for this convergence requirement
Size Gets Bigger
Machinability deteriorates, maneuverability deteriorates, and blind holes need to be buried 1. Cost increase 2. Difficulty in alignment accuracy
Impedance Accuracy
The etching challenge is great:
STUB (Impedance Is Not Continuous)
STUB is tightened, board thickness fluctuation is extremely challenging, and back drilling technology is required
Increased Signal Loss Demand
It is a big challenge for all copper clad laminates; the tolerance requirements for PCB thickness are high, including length, width, thickness, perpendicularity, bow and twist, etc.
The Number Of Layers Becomes Higher
Features such as denser lines and vias, larger cell size, thinner dielectric layer, etc., more stringent requirements for inner layer space, interlayer alignment, impedance control, and reliability
Accumulated Experience In Manufacturing Communication Board Of Huihe Circuits
High Density Requirements:
The influence of crosstalk (noise) will decrease as the line width/spacing (L/S) shrinks.
Strict Impedance Requirements:
Characteristic impedance matching is the most basic requirement for high-frequency microwave boards. The greater the impedance, the greater the ability to prevent the signal from penetrating the dielectric layer, the faster the signal transmission and the smaller the loss.
Transmission Line Production Accuracy Is High:
The transmission of high-frequency signals has strict requirements on the characteristic impedance of the printed wire, that is, the production accuracy of the transmission line is generally ±lmil, and the edges of the transmission line must be very neat, and no burrs, gaps, or repairs are allowed. line.
Mechanical Processing Requirements:
First, the high-frequency microwave board material is very different from the epoxy glass cloth material of the printed board in terms of machining; secondly, the processing accuracy of the high-frequency microwave board is higher than that of the printed board. Many, the general shape tolerance is ±0.1mm (in the case of high accuracy, the shape tolerance is ±0.05mm).
Mixed Lamination:
The mixed use of high-frequency substrates (PTFE-based) and high-speed substrates (PPE-based) makes the high-frequency and high-speed circuit board not only have a large conduction area, but also have a stable dielectric constant, high dielectric shielding requirements, and high temperature resistance. At the same time, it should be solved that the differences in the bonding force and thermal expansion coefficient between the two different plates lead to the undesirable phenomenon of delamination and mixed pressure warping during the processing.
The Coating Uniformity Requirements Are High:
The characteristic impedance of the high-frequency microwave board transmission line directly affects the transmission quality of the microwave signal. The characteristic impedance has a certain relationship with the thickness of the copper foil. Especially for microwave plates with hole metallization, the plating thickness not only affects the total copper foil thickness, but also affects the accuracy of the wire after etching, so the size and uniformity of the plating thickness Need to be strictly controlled.
Laser Micro-Via Processing:
The important feature of high-density boards for communication is the micro-via with blind/buried via structure (aperture ≤0.15mm). The formation of tiny vias is currently mainly laser processing. The ratio of the diameter of the via hole to the diameter of the land may vary from supplier to supplier. The ratio of the diameter of the via hole to the connecting plate is related to the accuracy of drilling positioning. The more stacks, the greater the deviation may be. At present, the target positioning is tracked layer by layer. For high-density wiring, there have been vias without land.
Surface Treatment Is More Complicated:
As the frequency increases, the choice of surface treatment becomes more and more important; a thin coating with good electrical conductivity has the least impact on the signal. The “roughness” of the wire must match the transmission thickness that the transmission signal can accept, otherwise it is easy to produce serious signal “standing waves” and “reflections”. The molecular inertness of special substrates such as PTFE makes it difficult to combine with copper foil. Special surface treatment is required to increase the surface roughness or add a layer of adhesive film between the copper foil and PTFE to improve the bonding force.
As a professional chinese pcb manufacturer, we provide bare printed circuit board, bare pcb board, audio circuit board,pcb audio, communication pcb and etc. For
different types of pcb boardor more information, please feel free to contact us!
Send product request
Other supplier products
 |
8 Layer ENIG Impedance Control Half Hole PCB | Number of layers: 8 Surface finish: ENIG Base material: FR4 Outer Layer W/S: 4/3.5mil Inner layer W/S: 4/3.5mil Thickness: 1.2mm Special proc... |
 |
PCB Prototyping | China high quality pcb prototypeFactory Has 97% On-Time Delivery Ratio In accordance with IPC standards, PCB prototype manufacturer strictly contr... |
 |
Medical PCB | Medical PCB Huihe Circuits has passed the ISO13485 medical device quality management system standard,Life support products or high-end products ... |
 |
Blind Buried Vias & Hdi Pcb | Blind & Buried Via Board, use micro blind vias to increase the trace distribution density. Improve radio frequency, electromagnetic wave interf... |
 |
Heavy Copper PCB | Heavy Copper PCB, pcb fabrication up to 12oz, large current, pcb fabrication base material is FR4/Teflon/Ceramic, pcb fabrication used in high-powe... |
Same products
 |
Header Card | Seller: Dongguan Xiaolong Packaging Industry Co.,LTD | Our new range of custom header cards and bagsis a high-quality printing paper that is excellent f... |
 |
Grey Cardboard | Seller: Dongguan Xiaolong Packaging Industry Co.,LTD | Grey cardboardis double grey industrial cardboard, which is produced from a kind of recycled wast... |
 |
Green Colored Paper Wholesale | Seller: Dongguan Xiaolong Packaging Industry Co.,LTD | Colour paper greenis perfect for kids who love to draw and do crafts. Its smooth and clean surfac... |
 |
Gift Paper Boxes | Seller: Dongguan Xiaolong Packaging Industry Co.,LTD | Gift-giving has been a tradition for centuries, and the perfect gift box of paper, it can make th... |
 |
Food Packaging Box | Seller: Dongguan Xiaolong Packaging Industry Co.,LTD | Food Packaging Box from Xiaolong is the perfect solution for anyone looking to transport food ite... |
